EVAPO-RUST® C700 Rust Remover, 946 ml

Product Information

Depending on the metal and the severity of the rust and the required level of de-rusting it can take anywhere from 12 hours up to as long as 1 week (or more) for the chemical reaction to finish Based on extensive research and years of development, this product has been proven effective to remove even deep rust on all types of mild steel and iron. After all procedures are done, take microfiber cloth and dry the place until it's not wet anymore. The only thing which is left is to put the new paint layer on the spot and you can do it immediately. As I stated earlier, the beauty of this rust remover is that you can reuse it. However, you need to do it properly. Keeping it in a separate container is one option, but there is another effective alternative. The removal of the rust (iron oxide) reduces the proportion of iron to carbon, leaving a higher concentration of carbon on the outer surface. This heavier layer of carbon could cause a darkening of the metal due to the attributes of the carbon. The darkening does not have an adverse affect on the metal. It merely represents the movement of carbon from the interior of the metal to the exterior of the metal.

Well, let’s start off with the competition. Products such as Metal Rescue, Loctite Naval Jelly, WD-40 and others tend to work out well. In addition, they don’t cost as much as the high-end products. However, they don’t perform the same on different metal surfaces. Moreover, some of them can take more than 24 hours to start having a noticeable effect. Since Evapo-Rust® is a highly effective rust remover, it stimulates the carbon migration process. Evapo-Rust®is not alone in creating the carbon migration effect. Other rust removal treatments will also result in carbon migration and a darkening of the metal. The primary difference between Evapo-Rust® and the acid based treatments is that Evapo-Rust® will not harm or weaken the metal. Unlike other treatments, Evapo-Rust® will not darken products made with low carbon steel. Now, the product CAN remove rust in cold weather, but the process will be a lot slower than usual. Moreover, if the plastic container with the metal item is out in the cold, it doesn’t speed up the process if you move it to a warm space. It’ll still take time to warm up, making the removal slower. If you have problems removing rust from certain metal objects, I’m sure you’ve had many people give you different suggestions. Some would share their homemade rust remover “ recipe” while others would praise a product or two. Then again, you’ve surely browsed the web for a solution and maybe even found videos talking about water-based rust removers and how spectacular they are. And one of the best, highest-rated water-based rust removers out there is Evapo-Rust. The product can be re-used until its effectiveness starts to wear off. In general, one gallon of Evapo-Rust® will remove 1/2 pound of pure dry rust. Since rust is 1/17th the weight of iron, the workload is quite substantial.

Getting rid of rust on metal parts of a car is real dream of many motorists throughout the world. You've always wanted some thing which would delete all damaged spots from your car's body and leave it clean for repairing. But as soon as you bought some liquids for huge amount of money, you got disappointed with what you really had as results. It is safe for the user and non-corrosive to steel. It does not harm brass, copper, aluminum, gold, lead, titanium, steel, cast iron, chrome solder points, vinyl, plastic, rubber, silicone, glass, cork, or wood. EVAPO-RUST® can be used over and over until it absolutely stops working. On average, one gallon de-rusts up to 300 pounds of light to moderately rusted steel.

SAFR is an automotive finish remover, i.e. its primary purpose is to safely remove any coat of paint from your vehicle. However, just like Safe-Erase, you can use it on walls, wood, plastic, and other surfaces. In addition, the process of applying and removing SAFR is the same as the one with Safe-Erase when it comes to vintage car paint. In short, you apply the gel, wait for a while, then scrape the debris off. On the other hand, there are some DIY solutions, like electrolysis and a vinegar-salt combination that seem to get the job done right. Of course, there are other methods that have been proven as myths, such as the Coca-Cola rust removal method. Personally, I’d advise using the vinegar-salt combo if you’re strapped for cash or simply can’t find Evapo-Rust anywhere. It’s by far the cheapest method, but it will take some time to work effectively. Before I do any submerging, I place the rusted piece inside of a container and mark the highest point it reaches; I leave the mark outside of the plastic container to avoid contaminating Evapo-Rust with the marker dye. I then pour the product, but I make sure that it’s a few inches below the marked point. Thanks to the Archimedes’ principle, the liquid will rise well above that point when I put the iron in. Step 2: Submerging the Item On the other hand, submerging the item halfway can actually work. However, you will have to flip the item over and submerge the other half as well. It’s a process that’ll take a lot longer than full submersion, but it still works if you have little Evapo-Rust left. Step 3: Give It Time reusable nature - you can use the liquid twice or three times after you pour it into some container until it gets dark;The wire brush was hard to get into the annular ring gear, but the rust is loose there. Notice how clear and readable the letting is. The final reason why so many people give this product a five-star rating is the fact that it’s so easy to use. Furthermore, it leaves no stains behind and the rust-free item will look brand new, as if you didn’t even use a remover on it hours ago. Where to Buy the Product