Intel NUC10i7FNH NUC 10 Performance Mini PC - Intel Core i7 Processor

Product Information

Although not extensively tested we did find that the built-in Wi-Fi worked well, and the WLAN module is capable of up 2.4 Gbps. The system has a three-year international limited warranty. x HDMI, 1 x SDXC, 1 x TB3 Type-C (rear), 2 x USB 3.2 Gen 2 (10 Gbps) Type-A (rear), 1 x USB 3.2 Gen 2 (10 Gbps) Type-A (front), 1 x USB 3.2 Gen 2 (10 Gbps) Type-C (front) The specifications of our Intel NUC10i7FNH review configuration are summarized in the table below. Intel NUC10i7FNH (Frost Canyon) Specifications

The USB-C port supports Thunderbolt 3 which allows it to drive two external 4K displays at 60 Hz or other Thunderbolt 3 compatible periphery. Initial Boot

Slot Kartu M.2 (penyimpanan)

Rather than struggle with an unsupported OS on this system, we installed Window 10 Enterprise on the system, updated Windows and the BIOS to latest version, and installed all the suggested drivers on it. NUC10i7FNH Performance Beberapa produk bisa mendukung Instruksi AES yang Baru dengan pembaruan Konfigurasi Prosesor, khususnya, i7-2630QM/i7-2635QM, i7-2670QM/i7-2675QM, i5-2430M/i5-2435M, i5-2410M/i5-2415M. Silakan hubungi OEM untuk BIOS yang mencakup pembaruan konfigurasi Prosesor terbaru. If you have already installed ESX (with a USB NIC for example) you can install the newer driver with the following command: # esxcli network firewall ruleset set -e true -r httpClient

It does have very good connectivity with its 3 external USB 3.1 ports and single USB Type-C Thunderbolt connector. It supports a single SATA drive, and a single M.2 drive. This is the first NUC system that supports 64GB of RAM. When the NUC has been shut down, the Data Rate LED stays Green (1Gbps). After completely removing the power once, the Data Rate LED stays off. The Activity LED is blinking green in both cases. For graphics install: (optional, MS default adapter will install and work ok for basic console scenarios**)** Requires ne1000 driver version 0.8.4-3, which is not bundled with any ESXi version at the moment. 0000:00:1f.6 Network controller Ethernet controller: Intel Corporation Ethernet Connection (10) I219-V [vmnic0]cpu0:1049180)vmw_ahci[000000170]: CompletionBottomHalf:TF/IF Error, PxIS=0x08000000, PxTDF=0x40,PxSERR=0x00400100, PxCI=0x00000000, PxSACT=0x0000000c, ActiveTags=0x0000000c this will give you device manager and make it easy, the FOD can be removed afterwards if so desired

cpu0:1049182)vmw_ahci[000000170]: LogExceptionProcess:Process: --|--|--|--|--|TF|--|--|--|--|-- (0x0020) Curr: --|--|--|--|--|TF|--|--|--|--|-- (0x0020) This morning, I updated to the latest BIOS version. I was hesitant to do this because it has not helped anyone in the past. Intel has another Comet Lake NUC called the NUC10i7FN K. Whereas the NUC10i7FN H has 2” tall case and a 2.5” SATA drive slot the NUC10i7FN K case is slightly shorter at 1.5” and does not have a SATA drive slot. The mainboard and the CPU are the same in both of these systems. Gen NUCs are equipped with an SDXC Slot. Unfortunately, there is no driver available for ESXi at the moment so it's not possible to use the SD Card slot. Your instructions worked like a charm. Below is the adjusted code so you can run the very latest ESXi 7.0 U1b from mid Nov 2020 on a NUC:The NUC10i7FNH SPECviewperf was less performant than NUC8i7BEH which has a more powerful GPU. When viewing the SPECviewperf test on the NUC10i7FNH the output looked fine and our ad-hoc testing proved that the NUC10i7FNH is very usable in normal day-to-day usage, however for heavy graphics such as video editing or CAD work the NUC8i7BEH would be a better choice. System and Maximum TDP is based on worst case scenarios. Actual TDP may be lower if not all I/Os for chipsets are used. NUCs have a very low power consumption. I've measured the power consumption of my NUC10i7FNK in 3 states: Idle (ESXi in Maintenance Mode), Average Load (1 vCenter, 4 Linux VMs) and during a Stress test. The NUC has been configured with 32GB RAM and no HDD or SSD. The power policy was configured to "Balanced". I have found a reproducible error pattern ... If I want to move a VM from another host to the NUC10, the process stops at about 30% ... Remove-EsxSoftwareDepot https://hostupdate.vmware.com/software/VUM/PRODUCTION/main/vmw-depot-index.xml