Silverline Pipe Bender Guide 15mm (MS124/15)

Product Information

Select several different angles to observe the coordination and consistency of the actions of each mechanism in automatic mode. After verifying that all items are normal, the equipment can be put into normal use. In the bending process, a mandrel is used to support the inner wall of the pipe bending radius and prevent its deformation. Without the mandrel, it is difficult to guarantee the quality of pipe bending. The pointer indicates the radius of the bending die, so if the bending die is replaced, the mandrel cylinder seat should be adjusted accordingly. The hydraulic system component can utilize either commercial accessories or aircraft hydraulic accessories. In the manufacturing process of power generation equipment, the cost spent only on the CNC pipe bender is very considerable.

In this industry, pipe benders are generally used to bend aircraft structural parts; these structural parts are generally large in volume, and aluminum alloy was widely used in the past. Adjust the required position and angle of the parts, and position the parts to the required length. The mold component is a supportive tool made from bearing steel or coil steel, depending on the surface diameter, and is heat-treated to achieve a hardness of HRC48~52.The machine tool must be properly grounded with a wire that is not less than 4mm2 in size and made of flexible copper cord. The voltage range of the power supply must not exceed the specified range, and the control circuit must not be tested with a tramegger, as this may cause damage to the device. According to the method of pipe bending, it can be divided into push bending, roll bending, press bending, and circle bending. Of these, circle bending is relatively easy to automate, so currently, bending machines are mostly designed for this method. The bending process principle is illustrated in a diagram. When cleaning the LCD, please cut off the power first, and do not clean it with liquid detergent or liquefied vapor. Only authorized personnel should make adjustments to the pipe bender or die, and one person should not make adjustments alone. The other operator must be at the control cabinet.

The Straightening Roller prevents vertical deformation during the bending process, and the use of a floating anti-ellipse fixture ensures that the steel pipe ellipse meets the required specifications after bending. In the process of pipe bender mold manufacturing, NC pipe bender mold is used in almost all links, such as forming mold, hot mold, cold mold, plastic mold, etc. In the inner compression deformation zone of the neutral layer, the thin-walled structure subjected to tangential compressive stress should not exceed the instability threshold, so as to prevent wrinkling.If the fitting requires a specific degree of ellipticity, the forming limit should be controlled to produce the desired distortion. When a pipe has only a few bending positions or several bending angles, there can be only one bending radius because the module of the pipe bending machine cannot be changed during the bending process. This is known as “one pipe corresponding to one die”. When operating the pipe bending machine, ensure that no one enters the space within the rotating arm’s sweep. All personnel must be prohibited from entering the area of the rotating arm and the pipe fittings while the machine is in operation. In addition to formers and guides, there are also a range of other spare parts and accessories available for pipe benders. These can include replacement handles, ratchets, and hydraulic cylinders, as well as spare batteries and charging kits for cordless benders.

Drive the collet clamping cylinder to observe the movement of its sliding sleeve and the reliability of the clamping.The numerical control pipe bender can perform winding bending with one or two bending radii for pipes in a cold state and is widely used in the bending of various pipe fittings and wires in industries such as automobiles and air conditioning. When using the Pipe Bender, high-pressure oil from the electric oil pump is sent into the working oil cylinder through a high-pressure oil pipe. This high-pressure oil pushes the plunger in the working oil cylinder to generate thrust, and the pipe is bent through the bending parts. During processing, the screen of the mobile controller displays the current processing value of the elbow, and it is possible to set single step action, half cycle operation, and full cycle operation. The entire machine tool can be lifted by threading steel wire through the bottom of the machine tool.

Add No. 20 mechanical oil to the revolving body and gearbox up to the centerline of the oil level indicator. The mobile foot switch has three functions: automatic start, emergency stop, and emergency stop, providing high safety. The pipe bender has several advantages, including multiple functions, a reasonable structure, and simple operation. Types of Pipe Benders In addition, automobile, adjustment train, general machinery manufacturing, and furniture manufacturing have become the main users of CNC pipe bender mold industry.

Sort By

Large circular arcs not only increase the workload but also are limited by the size of the tube bender. The bending process is performed using a bending die, clamping die, and pressure die. The bending die is mounted on the spindle, while the clamping die secures the pipe fittings to prevent any axial movement. The pressure die consists of a guide die and a follow-up die. During the bending process, the guide die applies the appropriate pressure on the anti-wrinkle die to the pipe fittings, and the follow-up die moves along with the pipe fittings. A mandrel is also used to fill the inner cavity of the workpiece and prevent any wrinkles, flattening, thinning or other failures during bending. There are several types of formers and guides available, including standard formers, multi-radius formers, and offset formers. Standard formers are used for making straight bends in pipes, while multi-radius formers are used for making bends with multiple radii. Offset formers are used for making bends that are offset from the center of the pipe. Spare formers and guides are essential accessories for pipe benders, as they help to ensure accurate and consistent bends in pipes. Formers are shaped pieces of metal or plastic that are placed inside the pipe to help guide it as it is being bent. Guides are used to hold the pipe in place and prevent it from slipping or moving during the bending process.