Quixx 10003 - Acrylic scratch eraser, 50g

Product Information

It’s important, however, to proceed with caution:Use the wrong technique, and you could dull the finish or create more scratches, worsening the problem. The goal is to break down the plastic just enough to even out the scratch and restore a seamless surface. So rather than trash those plastic items, get them looking good as new again with our tips for how to remove scratches from plastic. Tools & Materials If your scratched plastic is clear it is likely to be either acrylic or polycarbonate, which are the two most popular clear plastics. Scratches can be removed more successfully from acrylic than polycarbonate. Once polycarbonate is scratched it is not really possible to remove scratches. Scratches can, however, be removed from both clear and coloured acrylics.

Apply a coin-sized amount of scratch remover onto your rag. Acrylic scratch removers, such as Novus or Turtle Wax, help polish your plexiglass and buff out any light scratches on its surface. Squeeze a dime-sized amount onto the damp cloth, and rub it into the cloth to spread it. If you have multiple scratches you need to remove, use a quarter-sized amount instead. [9] X Research source If traces of a scratch remain, clean the area again and move on to a 1,000 grit sandpaper (the higher the number, the finer the grit), repeating the circular buffing motion and cleaning after each pass. Continue to use progressively finer-grit sandpaper, up to around 2,000 grit, until the scratch has completely disappeared. When the scratch has been smoothed out, clean the surface again with a damp cloth. STEP 6: Polish to renew sheen. This article was co-authored by Jon Gholian. Jon Gholian is a Cleaning Specialist and the Founder of Cleany, a home and office cleaning concierge service based in New York City, New Jersey & Miami. Cleany specializes in providing quality cleaning and handyman services to all their customers. All Cleany employees are insured, bonded, and professionally trained. Cleany has been featured in the New York Times, Bravo & Redfin. Apply a thin layer of plexiglass polish to the area. The area with the scratches will look cloudy when you're finished buffing it with the sandpaper. Apply a coin-sized amount of plexiglass polish onto a clean cloth and work it into the glass in small circular motions. Keep buffing the polish for 30 seconds or until it turns clear on your surface. Wipe the polish off with a clean, dry cloth to remove the scratches. [5] X Research sourceMake sure that the acrylic sheet is cleaned either with dish soap or Novus No. 1. Then, follow this procedure to remove moderately deep (under 5 mm) scratches from acrylic: Apply toothpaste to a damp cloth. A mild abrasive, like toothpaste, helps wipe the scratch away. Use a paste variety, not a gel one. You won’t need to put much on the cloth. Just use enough that you can smear it all over the scratch. Instead of toothpaste, you could also try: [5] X Research source Removing surface scratches from acrylic only requires a few simple tools and a bit of determination. In this how-to guide, we will walk through how to evaluate scratches and provide instructions for repairing light and moderate scratches in acrylic. product/helpAdviseTab.hbs -->

Whether acrylic plastic is being used for home use or commercial use, it’s an unfortunate reality that it may accidentally become scratched. Fortunately acrylic’s physical properties allow it to easily be buffed with special, slightly abrasive solutions. If a scratch is less than 5 mm deep, it’s a simple procedure to fix acrylic. Fortunately, it’s possible to banish such blemishes with a little elbow grease and a few household supplies as easy to find as opening up a medicine cabinet. (Hint: We’re talkingplain old toothpaste!)Novus plastic polish is a one stop solution for restoring and revitalising plastic products. Novus has been formulated to completely restore scratched, faded, or discoloured plastic materials. Angelwax says it can be used to remove up to 2,500-grade sanding marks. Along with the rest of the top four here, it topped the results for finish improvement, leaving a shine in stark contrast to untreated areas and most of its rivals’ attempts. It had trouble with the plastic ice scraper marks, but fared better on the fine knife line, where it only had to give best to ValetPRO. A competitive price was enough to give it a narrow victory over the similar Advanced Compound. Soak a piece of 800-grit wet/dry sandpaper in water for several minutes until saturated. Use a gentle, circular motion to sand the area, making sure not to apply too much pressure or you could introduce new scratches. Rinse between passes and re-wet the sandpaper as needed throughout the process. STEP 5: Go for a finer grit.

Cleaning Specialist Expert Interview. 15 December 2020. Gently rub it in a circular motion all around the scratch. This will remove any dirt and grease, making it easier to get rid of the scratch. Dry the area with a clean, dry cloth when you’re done. [2] X Research source You can use a microfiber towel. [3] X Expert Source Jon Gholian

Take a dry, clean cotton or microfiber cloth. Wipe away any fragments Warning: A dirty cloth could scratch the acrylic all over again! Finally, dry the area with a soft, dry and clean cotton cloth. Then apply the acrylic polish and the acrylic should look like it has never been scratched! The polish should restore your acrylic to a high level of shine.

Sand over the scratch in small circles for 1 minute. Apply light pressure to the scratches with your wet piece of sandpaper. Work in small, circular movements to buff the surface evenly. Sand any areas that are scratched for 1 minute, and wet the sandpaper again when it feels dry. [2] X Research source Alternate between the above two steps for about three minutes. Your acrylic may still look scratched – but we’re not done yet! If some scratches are still visible, get the sandpaper, water, acrylic polish, and a fresh, clean cotton or microfiber cloth. Then, follow these steps:

For deeper scratches to acrylic

Proceed to the next step if your scratches are pretty light or skipstraight to Step4 if you’re attempting to buff out a bit of a gouge. STEP 3: First buffusing a mild abrasive, like toothpaste or baking soda.