KNIPEX - 33 03 160 Tools - Duckbill Pliers, Chrome (3303160)

Product Information

The two types of recessed head screws in common use are the Phillips and the Reed & Prince. Both the Phillips and Reed & Prince recessed heads are optional on several types of screws. The Reed & Prince recessed head forms a perfect cross. The screwdriver used with this screw is pointed on the end. Since the Phillips screw has a slightly larger center in the cross, the Phillips screwdriver is blunt on the end. The Phillips screwdriver is not interchangeable with the Reed & Prince. The use of the wrong type screwdriver results in mutilation of the screwdriver and the screw head. When turning a recessed head screw, use only the proper recessed head screwdriver of the correct size. The most common crosspoint screwdrivers are the Number 1 and Number 2 Phillips. These posts outline the basic knowledge required in using the most common hand tools and measuring instruments used in aircraft repair work. This information, however, cannot replace sound judgment on the part of the individual, nor additional training as the need arises. There are many times when ingenuity and resourcefulness can supplement the basic rules. Sound knowledge is required of these basic rules and of the situations in which they apply. The use of tools may vary, but good practices for safety, care, and storage of tools remain the same. Our extensive range include all types, shapes and prices – from high quality to economical – for a variety of applications like cutting wire, bolts, plastics, pipes or sheet metal, twisting, bending, forming, depanelling, clamping or fastening, including diagonal cutters, round-nose pliers, crimping pliers, bolt cutters, stripping pliers, needle nose pliers, monier pliers, cable cutters, circlip pliers,installation pliers, diagonal cutters, combination pliers, needle nose pliers, cable cutters, water pump pliers and much more. For Electronics Manufacturing we offer Electronic needle nose pliers, Electronic diagonal cutter, ESD needle nose pliers, ESD diagonal cutter and VDE 1000V insulated pliers and cutters for electricians.

Duck Bill Pliers - Etsy UK Duck Bill Pliers - Etsy UK

So sometimes I use these scissors to trim the batting when making quilts as I can cut very close to the seams without cutting the thread or the fabric. Always keep the faces of hammers and mallets smooth and free from dents, chips, or gouges to prevent marring the work. As adults, we tend to take the skill of cutting with scissors for granted. We learned how to do that in kindergarten, right?KNIPEX, Stahlwille and Wiha pliers and cutters all stand for quality made in Germany. Knipex is considered the worldwide leading pliers manufacturer for professional users in trade and industry. To avoid damaging the slot or receptacle in the head of the screw, the use of cordless power drills fitted with a removable tip driver to remove or install screws is not recommended, as the drill does not have a slip-clutch installed. The drive punch, which is often called a tapered punch, is used for driving out damaged rivets, pins, and bolts that sometimes bind in holes. The drive punch is therefore made with a flat face instead of a point. The size of the punch is determined by the width of the face, which is usually 1/8 inch to 1/4 inch.

Knipex 81006 85mm - 140mm J4 Straight Internal Circlip Pliers

Related tutorial: Best quilt batting, types of batting for quilting, and how to choose batting for a sewing project Understandably, these are some of the most misunderstood scissors! They can’t be used in the same way that you use normal scissors – and they shouldn’t be used that way because their purpose is very different. The cordless hand-held power screwdriver has replaced most automatic or spiral screwdrivers for the removal of multiple screws from an airframe. Care must be exercised when using a power screwdriver; if the slip clutch is set for too high a setting when installing a screw, the screwdriver tip will slip and rotate on top of the screw head, damaging it. The screw should be started by hand, to avoid driving the screw into the nut or nutplate in a cross-threaded manner. In general practice, a pin or bolt which is to be driven out is usually started and driven with a drive punch until the sides of the punch touch the side of the hole. A pin punch is then used to drive the pin or bolt the rest of the way out of the hole. Stubborn pins may be started by placing a thin piece of scrap copper, brass, or aluminum directly against the pin and then striking it with a hammer until the pin begins to move.

Aircraft Maintenance, Aircraft Tools, Aviation Tools - Pliers and Plier-Type Cutting Tools

When using a screwdriver on a small part, always hold the part in the vise or rest it on a workbench. Do not hold the part in the hand, as the screwdriver may slip and cause serious personal injury. An offset screwdriver may be used when vertical space is limited. Offset screwdrivers are constructed with both ends bent 90° to the shank handle. By using alternate ends, most screws can be seated or loosened even when the swinging space is limited. Offset screwdrivers are made for both standard and recessed head screws. Ratcheting right angle screwdrivers are also available, and often prove to be indispensable when working in close quarters.