Beastmaker 2000 Series, brown

Product Information

Warm up on the climbing wall/fingerboard for at least 15mins. Take your time with the warm up. If you start training without fully warming up you are at a much greater risk of injury. Finger injuries are nasty and take a long time to heal. You should do your very best to avoid them. Provided our fingerboards are mounted correctly (i.e. on a plumb vertical surface), there can be a few reasons why fingerboards can feel different. Reducing hold size, adding some weight, adding an extra hang, hanging on for longer or reducing your rest time. Intuitive blending: each cycle is 60 seconds. After 20 seconds, the Beast slows down to let ingredients settle before blending again. This prevents ingredients from blending on the bottom but not the top.

Inside the tunnel, stay on the left side the whole time, hugging the wall on your left shoulder. Eventually you will meet an enemy who is trying to escape through the tunnels instead of running at you, armed. You need to take him out and loot his Keycard. This is the first of 3 that you require for the Blueprint. Finding Keycard B & C Practice using the handheld router on a piece of scrap first! If you are inexperienced with the router, practice first! Make sure that you can precisely create holes to the depth you want. Safe: the Beast monitors the temperature of what’s inside. This prevents overheating and expanding liquids.Reduce hanging time and increase resting time for each hang. Instead of 7sec hang and 3sec rest, hang for 6 sec and rest for 4, or hang for 5 and rest for 5. You can mix up the variables between sessions to keep the exercise fresh, while still training the same grip type. finger open handed hang on either hold 3 or hold 4 (2 handed hang using hold 3 or 4 for the left hand and the corresponding hold for the right hand). This is an open handed hang so don’t put your thumb over your fingers (i.e. the crimp position). Complete the set as detailed above. 3 mins rest.

The beauty of Beastmakers is that they can be easily restored to their original texture. All this takes is a (very) gentle sanding with some fine (120 grit) sandpaper. This only needs to be done when the holds feel noticeably different to the unholdable areas of the fingerboard. In reality this hardly ever needs to be done on a home fingerboard, but does sometimes need done on a fingerboard in a commercial centre. Each homeworld has specifically designed portals. In the original version, the portals in this homeworld are giant, carved wooden and stone arches and sometimes with tribal patterns. In the Reignited Trilogy, the portals are shorter wooden archways that have tribal patterns on the side and a green diamond-shaped jewel above the portal. Above the jewel is a Tiki face and some grass. There is also a green vine hanging over the portals. Hang with one hand in a similar, but worse hold , and alternate hands between hangs so each hand has hung 3 times off a smaller hold and 3 times off a larger hold. Each set = 7 second hang followed by 3 second rest, repeated 6 times in total. Rest for 10-15mins and repeat up to 3 times. Progression Techniques If you’re on the market for a new blender, the Beast Blender is a brilliant choice. It may be targeted to health-conscious smoothie lovers, but the Beast can do so much more. Anything that requires blending can be tossed in the trendy vessel, including frozen fruits and vegetables. The proprietary 12-rib design assures a smooth blend every time, leaving no ice behind.

finger hang on slopers (hold 5). Complete set as detailed above. 3 mins rest. To make these easier either pinch below the sloper with your thumb or nestle your index fingers into the edge of the inner sloper for extra grip. We tend to say that if you are bouldering up to Font 7C/V9 (leading French 8a/5.13), the 1000 will be the best board for you and if you are climbing 7C/V9 (French 8a/5.13) and above, the 2000 may suit you better. However, we know of loads of very strong climbers that only ever use the 1000 and loads of guys just starting out who get a lot out of the 2000. It’s up to you! Remember to concentrate on form . If you are training crimp strength, make sure your fingers are in the correct position during the exercise. If you are training half crimp, the same applies. Once your fingers fall out of the desired position, step off. Make the exercise easier then start again. The Beastmaker 2000 is not a hangboard for beginners, it has been designed with the input of some of the best climbers the UK has to offer. The result is a hangboard which tests the limits of finger strength and will help you towards your high grade goals.

You can use these in combination or on their own to vary the intensity of each exercise allowing a lot of adjustment to the difficulty. This helps you to avoid hitting plateaus in your progression. To make the exercises harder you can:

The fingerboards comes with the appropriate screws that are 5mm diameter. The 1000 series beastmaker has 2x50mm, 2x60mm and 2x70mm screws. The 2000 series beastmaker has 1x70mm screws and 5x50mm screws. The 2 most important variables are Edge size and Resistance , but the latter 3 are also valuable methods of increasing overall difficulty of the exercise. Pretty much any climber can use either the Beastmaker 1000 or 2000 to improve their finger and arm strength. However, we originally designed the 1000 to be an “easier” fingerboard and the 2000 to be a “harder” fingerboard. Now, put away the bottom board and take out the fresh top board. We will be making some through holes. Because the top and middle rows of holds on the Beastmaker 1000 are deeper than a single board, we'd have to drill through the top board, and then later align the holes with those on the bottom board.