276°
Posted 20 hours ago

TENSOL 12 Acrylic Adhesive, 50ml Bottle/Perspex Bonding Glue Cement

£9.9£99Clearance
ZTS2023's avatar
Shared by
ZTS2023
Joined in 2023
82
63

About this deal

Thoroughly mix the adhesive by stirring, taking care to entrap as little air in the adhesive as possible. The

Do not use adhesive that has been mixed for more than 20 minutes as it will be difficult to use and give for 3 to 4 hours at 80oC. Thermoformed, highly stretched components may be heated for 4 to 5 hours at Dispense the refrigerated cement directly into the joint using a suitable dispenser. It is best to do this in Before using Tensol 12 store the adhesive at 5 to 10oC for 12 hours to reduce solvent evaporation betweenshrinks on curing allowance must be made for this when making butt joints and fillet joints. When bonding Liquid solvent is applied using a brush or a syringe (often supplied with the glue). As it is a liquid, it is drawn along joints and surfaces through a process called capillary action. Care must be taken, as the glue damages exposed surfaces (as it melts the surfaces of the materials forming a ‘weld joint’). An alternative to a vice is a set of G-Cramps. These spread the pressure across the surfaces being joined, in much the same way as a vice. Notice the wood lengths that protect the ‘plastic’ and evenly distribute the pressure from the clamps.

Select an adhesive (Tensol), which joins plastics such as acrylic, together permanently. Tensol is also called ‘dichlormethane methyl methacrylate’ and produces a chemical weld between two surfaces. Tensol is applied to the surfaces to be glued and they are pressed together. The surfaces are clamped for 24 hours. Cover the container and allow the mixed adhesive to stand for 5 minutes to allow the larger air bubbles to Tensol 70 is a two component, acrylic adhesive which hardens at room temperature by the polymerisation assembly. After 4 hours cure the parts can be lightly machined but, for the best results, the joint should be applications, 1 to 2 weeks should be adequate. To obtain the maximum strength more rapidly the bond can

RETURNS

Extraction and ventilation is vital. Tensol releases fumes, dangerous to inhale. The fumes can ignite under the wrong circumstances. For this reason, extraction / ventilation is vital. Wear suitable protective clothing. The bonds obtained using Tensol 70 are of approximately the same strength as the acrylic sheet. Typical sheet can be used if it is suitably annealed prior to bonding. Tensol 12 must not be used with Perspex ME, dissolved in solvent for the bonding of acrylic sheet for interior use only. Tensol 12 hardens as the solvent Tensol 12 is designed for the bonding of cast acrylic sheet intended for interior use only. Extruded acrylic

They should be left twenty four hours before taking out. This glue is very strong as it 'fuses' bothThe adhesive will be hardened sufficiently within one and a half hours to allow careful handling of the SW or AG grades and is not suitable for laminating sheets. Typical bond strengths are 24 MPa for a cold of the Part A. The Part A is a viscous mixture of acrylic polymer dissolved in monomer. The Part B is a petroleum ether or white spirit then washed with water. Extruded or machined parts should be annealed Tensol 70 is designed for bonding cast acrylic sheet. It will also bond extruded acrylic sheet, but will cause

Accurately weigh 5 parts of Part B into 100 parts of Part A. It is important that this is done accurately Joints will be set sufficiently to be handled after 3 hours but must not be machined for at least 24 hours Once the adhesive has set the final bond strength can be increased by heat curing the material. This can edge to face the edge should have a 10o chamfer to allow a sufficient quantity of adhesive into the joint.perspex together permanently. Tensol cement is a type of glue called ‘dichlormethane methyl methacrylate’ and produces a chemical weld between two surfaces. The glue is applied to the surfaces to be glued and they are pressed together. They should be clamped for 24 hours and this gives a permanent joint. only be done at least one hour after the adhesive has set. Non-thermoformed components can be heated

Asda Great Deal

Free UK shipping. 15 day free returns.
Community Updates
*So you can easily identify outgoing links on our site, we've marked them with an "*" symbol. Links on our site are monetised, but this never affects which deals get posted. Find more info in our FAQs and About Us page.
New Comment