Fluval spec nanoaquarium, 19 liters

Product Information

The technical answer to this is that depends on many factors: how much internal heat gain from your equipment/lights, how cold you keep your house, what temperature you keep the aquarium at. However, if the aquarium is controlled by a thermostat, you can oversize a bit and cover a wide range of conditions. If you want to run this as a tropical tank you’ll need a heater – The recommended one for the tank is the Fluval Edge 25w Heater – Buy it here. Some stats on the latest version of this tank Once the tank is clean, the next step is to get the filter fitter correctly. Before you put it in set the flow rate on the filter box if you’re unsure just start it in the middle of the setting.

Currently have 2 threadfin rainbows, 3 danio galaxy, an oto, and 2 CRS and 3 ghost shrimp. Since setting up the tank I’ve only lost 1CRS to what looked like a molting problem, but that was just a couple of days after introduction - the other two have seemed fine for 2 months now. It’s really easy to clean and maintain and due to its size water changes and filter cleans only take around 15 minutes. Use a clean cloth and just water, rinse out and clean over the tank thoroughly. Rinse over the filter sponges and replace them as they were. Step two – Setup the filter Having said that, I still wholly recommend utilizing a good temperature controller. Most aquarium controllers can also be paired with fan to provide cooling control. It adds peace of mind and greater consistancy for temperature making your fish and inverts healthy.In a search to find a heater that is small enough to fit in the pump section of a Fluval Spec aquarium, you will come across some models that are do not have an internal thermostat and are thus always ‘on’. They are small, simple, and usually have very low power of around 10-20 watts. I would avoid these. I’m not averse to using a heater that is a bit underpowered as I think that most heaters are oversized for the heat loss experienced in the winter. However, without the ability to adjust with changing conditions, you will not be providing your aquarium inhabitants with temperature stability. As the environment changes with light schedules and room temperatures, the heater will always be on and will not alleviate these fluctuations. I don’t see much benefit in them and suggest you find a way to control your heater, either with a model that has an internal thermostat or by an external temperature controller. Accuracy and Reliability: The pump sits next to the filter in an empty chamber and I have to confess I'm twitchy about it. I've had bad experiences with pumps of this nature, so the proof will be in the long-term pudding. If you hate the frosted glass, and you want to try out the idea in #1 (keep in mind that is kind of a permanent mod..) you can put normal scotch tape on the frost, and it makes it see through again. I personally like it the way it is, so I haven't done this. N30 provides expertise in the construction of large acrylic aquariums, such as those in Underwater World (Resort World Sentosa). We supply customised storage tanks to fish farms such as Qian Hu, and to major restaurants. The N30 brand name is trusted for quality workmanship in the industry. There are two ways to combat this problem. The first is to invest in an aquarium heater that has advanced electronics for the temperature control. The problem is that most heaters in this category do not fit in the pump section of the Spec. The Eheim Jager is a great example of one that does offer better reliability and control, but unfortunately does not quite fit in the Spec V.

Ultimately it's your choice. I feel the Fluval is worth the price, as most things in this hobby tend to be.

Then used some bubble wrap to pour the water over to avoid disturbing the setup I have (This is my top tip for filling your aquarium!). A disadvantage to both the DIY temperature controller and a reefkeeper type controller is that they take up space outside your aquarium. I have dealt with this by putting everything into a storage box to hide it. It comes in 2 sizes, 19 litre and 10 litre and a choice of colour. I’ll be reviewing* a white 19-litre tank that will be set up as a tropical step. This is a traditional looking compact aquarium that can be touched up or enhanced with lights and other accessories. There are a ton of Fluval-branded matching accessories you can use with the Fluval Spec aquarium.

I think this is the preferred method for putting a heater in your Fluval Spec – it keeps things tidy and clean in appearance. Things get somewhat tight in the pump section of Fluval Spec aquariums, what with the pump and outlet tube traveling up from the pump occupying part of the space. I found that there is enough room for a heater, but you have to look for ones that are small enough. You’ll need to tank this on and off to do water changes, float new fish, clean the filter and its easier to take it off to clean the glass too.I would also love to hear people's opinions on which wattage to use for a 5 gallon tank such as this and what they've found worked. I am housing one Betta fish so the temperature needs to be around 26 degrees celsius (between 78-80 degrees Fahrenheit). Ive heard people use both 25 and 50, but 50 sounds like the safer option. Once again I'm not sure!