276°
Posted 20 hours ago

Cloudray Ruida RDLC320-A Co2 Laser DSP Controller for Laser Engraving and Cutting Machine

£9.9£99Clearance
ZTS2023's avatar
Shared by
ZTS2023
Joined in 2023
82
63

About this deal

g. Divide your current steps per rotation by the value obtained in step e. (e.g., 5000 / 1.1875 = 4210.53) Now, there are three ways that you can connect to the machine and get your programs from the computer into the brain.

If you are installing a new controller into a machine, you will need to perform the configuration that is normally done for you by the factory. Once the multiple- origin logic is selected and if the serial number of the next origin is 1 and four origins are enabled, when the memory file function is started or the processing file is uploaded into the PC and this file selects “Take the Original Origin as current Origin”, the work started for each time will use When the laser is a glass tube, if the used laser is outputted in the low-level form, this pin will be connected with the laser power enable end and used to control the ON/Off of laser. The Z/U key can be pressed when the system is idle or the work is finished. On pressing this key, it will show some entries in the interface, each entry includes some functions, Z axes move, U axes move, each axes to go home etc.; Squares are rectangles and my circles are ovals - Steps per rotation for your machine must be adjusted for designs to be properly sized. Each machine and rotary is different. Below are steps to help calculate steps per rotation.

Recommendations

Idle Move Speed: this parameter decides the highest speed of all non-lighting lines for the machine in the movement process. There are only 4 possible combinations of "limiter polarity" and "direction polarity" for each axis. I can't tell you which is the correct combination, but change those settings for the X axis until it moves properly when you power the machine, then do the Y axis. Once these are set, the next steps are easier. Cover Opening Protection: If enabled this item, the controller must connect the protection wiring, otherwise, the machine will not work. After the manufacturer regulates all parameters of the machine well (including all manufacturer parameters and user parameters), this function can be used to store the well-regulated parameters to help users to recover the original parameters (including all manufacturer parameters and user parameters) through selecting “Recover Para” when they regulate The Ruida RDC6442S controller is a popular controller used in laser engraving and cutting machines. If you want to upgrade the firmware of your Ruida RDC6442S CO2 laser controller, follow these steps:

Laser won't fire at slow speeds . Ruida has a feature called Start Speed which may prevent the laser from firing at speeds lower than 10 mm/s. Setting your min and max power to the same value and this should resolve the issue. The Ruida Classic Design RDC6442G is a CO2 laser controller with a 3.5-inch color screen and the software RDWorks is included. It is suitable for various laser applications such as cutting, engraving, and welding. It requires a power input of +24V and a current of greater than 2A. The operating temperature range is 0 to 50 degrees Celsius and the maximum humidity should not exceed 70%.You will also need to set the 'Max Travel' value for the X and Y axis - these numbers dictate the length of each axis, and together define the size of the work area of the machine. Step Length Calibration ¶ When the cursor stops at “Auto Focus”, press the Enter key to search for the focus automatically. Language Setting If you need to reset your Ruida Controller to it’s DEFAULT Parameters as defined by your Laser System Manufacturer. This is the procedure to follow:

The Ruida controller, renowned for its quality and reliability, stands at the forefront of this technology. Powerful and Versatile: The Ruida Controller So as you can see already with just a few simple descriptions, we’ve covered most of this circuit diagram. Now just down here, Need more overshotting or larger acceleration (grammatical error intended) - Like the NOT ENOUGH EXTEND SPACE error, t his error occurs when the design is too close to an edge of the bed . This error message refers to Overscanning or Overshoot. When the laser is engraving, it may require extra space on the sides to get up to speed before the engraving starts, and to slow down and reverse after the engraving is finished. If the design is too close to the sides of the machine, the overshoot distance may result in crashing the machine. Increasing the acceleration or reducing the speed will both reduce the amount of overshoot space required. Depending on the design, the error may not always occur immediately.

Layer management: RDWorks includes a layer management system that allows you to organize your designs into different layers, making it easier to edit and control the different parts of your design. Cooler Error 1 Worked Paused - This error occurs when the chiller isn't on or water is not flowing through the water sensor connected to the Ruida panel. Ruida RDC6332M hybrid cutting controller is a hybrid cutting system based on the proven RDC6332G co2 laser controller, which is specially developed to combine the processing of sheet metal and non-metal cutting. Based on this co2 laser DSP controller, it can realize metal cutting and non-metal cutting. When work is idle or finished, all keys can be pushed, users can select a file to run, set some parameters, preview to a select file etc. But, when work is running or paused, some keys will not respond when they are pushed. Speed Setting They use a direct analog naught to five volt signal to send it to the power supply via the same in-terminal.

Set Origin 1/2/3/4: after the multiple- origin logic is enabled, you can stop the cursor at “Set as Origin 1/2/3/4”. Press the “Enter” key on the keyboard and the system will take the coordinate figures of current X/Y axis as the corresponding ones to the origin 1/2/3/4. Files can be imported into RDWorks, enabling use of any preferred software to design files. This is especially useful for businesses and educational organisations that may choose to update or change their design software. RDWorks offers the following functionality: We’re not really going to bother with it too much, except to say that it is an alternating signal which is generated by the controller, RDWorks is a software program used to create and control the operation of laser cutting and engraving machines. It is commonly used in the fields of woodworking, metalworking, and manufacturing. Some of the features and specifications of RDWorks include: RDC6332M hybrid cutting control system is a set of hybrid cutting systems specially developed by RuiDa Technology based on the mature RDC6332G control system, combined with the processing technology of metal sheet and non-metal cutting. Based on this controller, it can realize metal cutting and non-metal cutting. Function description

Features

When purchasing a laser with a DSP controller installed, the factory making the machine configures the laser controller for you to tell the controller how fast and in what directions to move, where the homing switches are, and so on. Now, on some of these controllers, if we look at Terminal one, on CN5 in this particular instance, it’s shown as a ground line. This system supports such file formats of Udisk as FAT32 and FAT16, but it can identify them when the files are put under the root directory of Udisk. The file name of more than 8 characters will automatically be cut out by the system. The file name that has only English letters and digits will not show when they are copied to the controller. The files copied from the controller to Udisk will Idle Move Acceleration: it means the highest acceleration of all non-lighting lines. Idle stroke speed and idle stroke acceleration can be set higher to reduce the working time of the whole figure, but if they are

Asda Great Deal

Free UK shipping. 15 day free returns.
Community Updates
*So you can easily identify outgoing links on our site, we've marked them with an "*" symbol. Links on our site are monetised, but this never affects which deals get posted. Find more info in our FAQs and About Us page.
New Comment