Blue Diamond Screw Tent Pegs - 20 pack, Purple, One Size

Product Information

I have tried using the common screw pegs on hard standing with little success. They just seem to spin like crazy but not grip and screw in. I also managed to drive the Dmax over one of them, and bent it pretty badly, but otherwise they are going well! Where can you buy screw in tent pegs from?

Compared to large, traditional pegs, these drill in tent pegs are much lighter, and you get away with much smaller pegs as they provide far more grab into the ground than a traditional peg. I’d have no issues using half size screw in pegs, as long as the ground is solid. Using Screw in Tent Pegs Peggy Peg also do a plastic fibre glass version but I suspect they would disintegrate in a typical hardstanding pitch.

These probably take a similar amount of time to put in as a traditional peg, but its less effort, and the removal is where they are really valuable. We use screw in tent pegs to hold the shower and toilet tent down DIY screw in tent pegs The first pull was set to be pulling the peg out of the ground at a 45° angle, replicating use on a tarp, awning or tent – in effect, trying to bend the peg as well as pulling it free from the ground, and that’s a no-no for some of these pegs.

Anyone found any pegs that screw in with minimum effort and hold? Or can someone explain how they manage with the common screw pegs? The major issue with traditional pegs is that they can be a mission to pull out. Sure, you can use another peg to make it easier, or a peg removal tool, but sometimes you still struggle for a long time, and that’s not much fun. The screw in pegs simply unwind, and cause you no stress or issues at all. Light weight To install them, just use the drill to wind the screw into the ground, at a 45 degree angle, or a little more vertical and hook what you need onto them. With our previous soft floor camper trailer, we had to put pegs into the corners of the tent as a minimum, and I had some big 12mm steel pegs that were about 400mm long.No doubt there are a couple of best screw in tent pegs, but for us the Bunnings Whites option works just fine. Simple, easy to use and strong as Should you get a set of screw in pegs? But maybe my insertion technique is wrong. I'm using a cordless drill and even at low speed they don't grip and screw in. So I ended up banging them in. It is easy to sweep because it is taught across the ground and it is no longer a trip hazard as it was before. Screw In Pegs are a galvanised 200mm-long shaft that accepts an included 5mm hexagonal driver, and both standard drills and impact drivers for great drilling forces. While looking a little agricultural, the cleverly designed wires loop and hook remains on the peg shaft and can be used to attach a guy rope, or to hold a tarp down directly to the ground. A great design idea sees the hook pointing downwards so as not to promote toe-stubbing. Although the Screw In Peg performed faultlessly in harder soils, the performance in anything softer is not much different to a standard peg. The finer flutes on the shaft clogged with dirt, rendering it of little use for ground-holding ability.

The slightly smaller ones for all the general securing of the walls and the smaller diameter ones for securing the floor matting. You can manually install some of these, but it takes more time, and unless you are very limited with what you can take, a drill is well and truly worth throwing in. Peggy Peg offers many different lengths and diameters, as well as aluminium and UV reinforced fibreglass pegs. A great design feature is the rope clips that slot over the hex-shaped head onto the main shaft. The clip can be used anywhere on the shaft meaning the peg doesn’t have to be drilled all the way in to still allow a pull from ground level, which will reduce potential peg damage. Attaching to the clip is a guy rope ladder, which replaces the steel spring on most guy ropes. We are very pleased with our Bunnings Screw in Pegs, and have recommended them to a heap of people already. After several years of using these, I finally broke a couple. The first one snapped from too much torque on the drill, trying to go into seriously hard ground, and it basically just twisted the steel off.A huge number of people travelling these days carry 18V drills, and winding a few tent pegs in and out is easy work. These can double up for winding the caravan or camper trailer legs down, repairs and maintenance on your gear and don’t take up much room. I’ve lost count of the number of tent pegs that I’ve bent, or flattened so badly that they’ve snapped from smashing them into the ground. If you’ve not used them before, know that everyone who has them raves about them, for good reason. Over the years, camping has become so much easier, and more comfortable, and little inventions like this go a long way to making this happen. The small clips that may be used in conjunction with the screw pegs are extremely handy for different applications. Some tents don’t have the ability to hook it over, so you may need to run the screw down in the centre of the loop, being careful that it doesn’t grab the fabric and start to twist it around!

I had a couple of guys who doubted how secure these pegs would be until I challenged them to join forces and pull them out. Being a screw-in design, a hammer is replaced by a 12V drill, although a shifter, spanner, ratchet or a hand brace (like your caravan leg winder) can be used to insert and extract the pegs.Blue Screw offers two plastic pegs at 310 and 580mm long. They are ideal in sandy environments with exceptional high-hold abilities. Blue Screw suggest its pegs work well in snow, sloppy mud and underwater too, which would be ideal for a boat mooring. The rope hook on top is large enough to attach multiple guy ropes. This product is aimed squarely at sand and soft soil use; forget trying to twist it into hard ground – it simply won’t work. As the Blue Screw is so flexible and long, you need to ensure it’s wound all the way in if pulling it at an angle, but works equally as well if screwed in line with the rope pull instead of at an angle, which could bend or twist the shaft beyond its limits. The main reason for the drill driven tent pegs being so good is they can be used in hard ground. This means crushed limestone, gravel or even compacted dirt is no issue at all. Over the couple of years that we had it the corner that you hit got so flattened down that they would snap off, and you’d be left with just a piece of straight peg. Easy to take out Peggy Peg can even supply long masonry bits to pre-drill holes into ridiculously hard ground. A combo tool can be used to help twist the pegs into the ground should your drill not do the job and there are purpose-designed anchor plates that accommodate up to seven separate pegs for extra ground-hugging force as well as slots to take awning legs. I have seen people make these up using long tek screws and washers welded to the top, but for the price that you can buy them I really don’t see why you would. I’ve snapped and bent a couple