Home Smart – D Mould for Windows, UPVC Plastic, 28 mm, 5 mm

Product Information

Our D shaped Mould creates a professionally neat finish with colour-coded match to ensure your room is completed to a top standard. The main disadvantage of this method is the chip shop odour that is likely to be left behind, although this will fade after a time. Again, this is a method best suited to mild cases of mould. 3. Revisit your chemistry class

Many people swear by baking soda (also called bicarbonate of soda) for removing a whole host of household nasties, mould included. Baking soda fights bacterial growth," confirms Chris Michael. "All you need is a spray bottle, some lukewarm water and around 1/4 tablespoon of baking soda. Fill the bottle, add the soda and shake well. Then use as you would a dirt remover spray." First, because mould can be nasty, and because some of the products to deal with are strong, it’s important to wear gloves when you clean. You might also want to wear a face mask so that you don’t breath any of the mould in. This is particularly important in areas with a lot of mouldy growth," advises Chris Michael. 1. Dig out the baking soda Tough 25mm wide, 5m long plastic d-section, rounded along both edges, d-mould is perfect for concealing butted joints on uPVC windows frames and when both edges will be visible. Available in a wide range of colours to match existing frames. Do take care when using some of the more potent formulas and open windows to get some fresh air flowing through the room. Depending on the product, it is often necessary to leave the solutions to get to work for a while before wiping them away.A cover mould can be used on its own to add decoration to your room or furniture or be used to compliment existing mouldings such as architraves and skirting

If you fancy giving this method a try, wear gloves and old clothes and keep children and pets well away. Generally, a minimum of 20 minutes on walls and shower mould, grout etc… If possible, for outdoor concretes and driveways leave on the surfaces for a minimum of an hour but, if able, leave it for the weather to remove. Baking soda is good for more than just biscuits —it also serves as a natural disinfectant thanks to it having pH levels of 8-8.1, which is too high for mould to survive, according to experts in ventilation, Envirovent. Bleach is usually a staple product in most people's cleaning cupboards, but does it work on getting rid of mould? Although it is a good idea to start with gentler, natural remedies, on stubborn areas of mould, a stronger solution may be required. (Image credit: Getty) 2. Vinegar could be your best friendA paste of vinegar and baking soda can work wonders on mouldy grout. (Image credit: Getty) 4. Use bleach — with care The acids in vinegar are good for breaking down mould," says Chris Michael. "You can put neat vinegar onto the mould, leave for a while and then wipe off. Regular household vinegar is fine – you don’t need anything special." Using our high-quality range, it guarantees you peace of mind that you are going to finish your project with professionally manufactured products to make any house a home! You can try this method for removing mould on skirting boards, walls, around windows and even on fabrics. Aim for a ratio of two cups of water to 1/4 tablespoon of baking soda and scrub the affected area with a brush, before rinsing clean and treating the area again for good measure. Using our Mould, it allows you tolerance when cutting for your walls and helps provide a consistent finish to any room, concealing all signs of silicone/sealants.

When it comes to removing the paste, use a stiff-bristled nail brush or an old toothbrush to scrub the paste and mould away. Finally, use a clean sponge, dampened with cold water, to rinse the are clean. Tough 25mm wide plastic d-section, rounded along both edges, d-mould is perfect for concealing butted joints on uPVC windows frames and when both edges will be visible. Available in a wide range of colours to match existing frames. The Trade Superstore Online Building Plastics products supplied by E Profiles Ltd are produced in accordance with a BS EN 1SO If you don't want to go out and buy a specialist mould removal product, you can give clear (don't use blue toilet bleach!) bleach a go," says Homebuilding & Renovating's Amy Willis, , who has tried various mould removal methods in her own home. "You'll need to use one that contains chlorine as this is the active ingredient, according to H&G." A cover mould is a multi purpose piece of timber which is typically used as a decorative finish on surfaces such as walls and ceilings as well as on timber furniture. Use our cover mouldings to add that finishing touch to your projects.

Excess humidity: Too much humidity causes damp — and damp causes mould. Aim to reduce the moisture in any rooms harbouring mould. A dehumidifier is a good investment in rooms with condensation and damp problems. Another benefit of this method is that it helps eliminate any musty odours associated with mould — plus it is safe for those with pets and children.

Poor ventilation: Good ventilation is key to keeping rooms fresh and condensation, damp and mould-free. Good extractor fans, MVHR and dehumidifiers can all help —as can regularly opening windows. Our Pine products are made using a lightweight, straight grained softwood which is easy to work with. Due to its strength, elasticity and relatively low cost, pine is a popular choice to be used in a variety of projects.However, it can be a great way to get rid of light mould stains in bathrooms and on grout. On tougher stains bleach will not always get rid of them all together, as Amy found out when trying the technique out on her bathroom ceiling. Our light hardwood is both a light weight and strong timber which is easy to work with and a good, natural lustre. Because of its strength to weight ratio and relative inexpensive price the light hardwood is a solid choice for a wide range of uses.