276°
Posted 20 hours ago

Vitrex 10 2280 Grout Finisher, Blue

£1.25£2.50Clearance
ZTS2023's avatar
Shared by
ZTS2023
Joined in 2023
82
63

About this deal

As mentioned above, it's best to use a squeegee or grout spreader as this will give the best finish. 'Applygroutwith a suitablegroutfloat, working in all directions across the tile jointstoensure that thegroutcompletely fills the joints,' advises tile expert David Talbot. Grout sponges are intended for wiping off excess grout, so when it comes to size, choose a big sponge if you need to worry about cleaning up a large tiled area or opt for a small sponge to reach narrow nooks, crannies, and tight corners. If the sealer leaves any hazy or white splotches on the tile, dampen a clean cloth with a bit of the grout sealer, and wipe the area until the blotch is gone. Now wipe the tile with a clean, dry cloth to remove any lingering residue.

You can chip out old grout with a hammer and screwdriver but a grout removal tool is a better option. This has a metal blade with a rough edge. Place on the tile grout and use a sawing motion and angle left and right to remove the grout. The Aqua Mix Sealer's Choice Gold takes the top spot for its natural looks and extensive protection. This product is a water-based sealer that provides ample protection over the entire surface, including grout and tiles. It also dries with a no-sheen finish for a natural, non-slippery look and feel. For ceramic tiles, this will provide additional protection against staining and wear, and it can be used with stones such as granite, marble, masonry, and limestone. Use this as a pre-grout sealer on your tiles for extra protection in areas such as bathrooms or kitchens. It's available in several different sizes from pints to gallons.It is best to choose a grout colour that suits the tiles for the project so that the grout blends into the floor pattern. Of course, you can also use this easy-to-apply, fast-drying grout sealer spray on existing grout. It won't change the appearance or leave haze on the surrounding tile, whether that's natural stone, ceramic or porcelain tile, or masonry. As a bonus, the product sprays on without much over-spray and requires very little cleanup. Don’t overlook the following guidelines on how to put grout between tiles! Make sure the old grout is removed (if re-grouting an existing tiled floor) When spreading the grout into the joins and removing any excess grout from the tiles, make sure you’re holding the grout float at somewhere between 45 to 90 degrees. Grout floats can have enclosed, rounded handles in the center of the float or they may have long, open handles that attach to the center or one side of the grout float and extend out from this point. Both styles are suitable options, though grout floats with open handles are easier to use in tight spaces, while enclosed handles offer improved control.

Finish by wiping across the tiles in a diagonal direction, rotating the sponge to its clean side after each swipe. Before moving onto a different section, rinse the sponge in water and wring it out until it’s almost dry . Eddie McFarlane, Strategic Advisor for Provider Experience at HomeX, adds, "You’ll want to decide on a layout before you get started. We recommend testing the layout in your space beforehand to make sure it’s exactly what you want by first laying the tile pieces in place without mortar or grout. Make sure you have the right tools on hand: a tile cutter, a rubber mallet, tile spacers, a level, a tile trowel, and mortar. Above all, take the extra little time to clean your tools after use. A dry piece of mortar coming loose and getting on your fresh floor can be very annoying.” Note: the time intervals for applyinggrout, wiping off excessgroutand polishing/buffing tiles during thegroutingprocess can vary dramatically dependent upon the temperature, humidity, type of tile beinggrouted, type ofgroutbeing used, width of tile joint and other factors so it is importanttostart on a small inconspicuous areatoassess the likely curing times for each process.' Can you put tile grout over old grout? If using powdered grout, mix up just as much as you’ll be able to use in 20 minutes (it’ll start to harden after that). Apply a blob of your mixed powder or ready-mixed grout to a grout spreader (using a scraper or grout trowel). Use the spreader to work the grout into the lines, going over the tiles with the edge to clean off excess. 4. Clean and leave to dryGrout—typically either a mixture of sand, water, cement, and color, or an epoxy base mixed with a hardener—is the filler used to seal the spaces between ceramic tiles on floors, counters, walls, or tub surrounds. Grout helps keep tiles in place but is not the same as mortar, the adhesive that actually glues tile to the underlying surface.

Start by mixing up your grout. Most come as a powder you mix with water; follow the manufacturer’s directions exactly—don’t add more or less water than called for. The best way to start building your grouting arsenal is with a whole grouting kit that provides everything you need to get going. These kits will often come with an assortment of floats, containers, bags, and pads necessary to contain and spread the grout evenly onto the work surface. The Barwalt Ultra Grouting System takes the top spot since it is a reliable and affordable kit for beginners and advanced users alike. According to the company, this system can cut down your work time by as much as 50 percent; that's a lot of time you could be spending doing something else. In our opinion, it is imperative that professional tilers are 100% confident when grouting tiles before agreeing to lay a customer’s floor. Wet your applicator with the grout sealer, and begin wiping the liquid into the grout lines. If you are sealing both horizontal and vertical surfaces, start with the vertical tile.Removing old grout means regrouting tiles and this is a messy job. So make sure that you have a dustpan and brush handy at all times. First remove any furniture or obstacles so you have a clear floor space to work in. Control is key for any type of DIY project, which is why it's necessary to consider the type of handle and whether it has any padding to improve user comfort or a textured grip for enhanced control. The size of the joints between tiles will determine what grout you need to use (Image credit: Getty Images) How much grout do I need?

Top tip: If you’re working with a large surface area, opt for a professional float when it comes to choosing your grout tools . Work in 5 to 10 square-foot sections and avoid running the grout float in the same direction as the tile joints – as this will create uneven coverage. At UK Pro Tiling Training, we train our students to become efficient tilers and credible in the trade. Tilers who have trained with us will know exactly how to grout a floor. Grout isn't only for the indoors; if you have an outdoor kitchen, counter, built-in fireplace or fire pit, or a tiled decorative trim, then you need a sealer that can keep the grout looking its best. For those situations, it's hard to go wrong with Serveon Sealants H2Seal All-Purpose Stone Sealer. This water-based, low VOC sealer dries clear, leaving your grout's color unchanged but providing excellent protection against damage from water—even saltwater—stains, and general grunge. Don’t just use the last tub of grout you opened! For the amount a customer is investing in the entire floor, an extra pot of grout won’t make a huge difference. Use a sealer rather than grout release if you want to enhance the color of stone or leave a “wet” looking finish. You may have to apply another coat of sealer after grouting for maximum protection and to enhance the color of the stone. Required Tools for this ProjectLet the sealer dry for the time recommended by the manufacturer. This is typically anywhere from 15 minutes to an hour.

Asda Great Deal

Free UK shipping. 15 day free returns.
Community Updates
*So you can easily identify outgoing links on our site, we've marked them with an "*" symbol. Links on our site are monetised, but this never affects which deals get posted. Find more info in our FAQs and About Us page.
New Comment