DYNAGEM polyWatch Watch Face Scratch Remover and Repair Polish

Product Information

Article size of the abrasive material so that you correct the larger scratches first and then get finer and finer to finally achieve a high shine with the final grit size....I would be skeptical about a single paste, unless perhaps the paste is made up particles that break down into smaller and smaller particle sizes as you work it into the crystal. I will sometimes, depending on the watch, use a coarse as 400 grit to start - all done by hand and you do need to be careful not to overdo it. It looks worse before it looks better: Polywatch alone does remove the tiny scratches and gives a nice overall finish, sort of like a coat of wax on a car finish.

I have lenses scratched by my glasses. Both in the upper middle of the lens. You mention blur... and VR headsets are already blurry. Will using this just cause worse blur so that trying to look through the scratches might be better? One tube of PolyWatch can be used for approximately 10 watch crystals (depending on how much you use and how deep the scratches are). PolyWatch is a cream that contains a very light abrasive material that will gently but effectively grind down your acrylic/plastic watch glass crystal, resulting in a scratch-free finish.Generally, polyWatch fills in the scratches. PolyWatch is a repair tool for watch scratches so the blur is a side affect. I have not tried using polyWatch on my lenses so don’t take my word for it but from what I know it shouldn't intentionally cause blur. You must remove all scratches at one grit, before moving to the next, and eventually you will get it clear: It looked very similar to your watch. It took me about 45-60 minutes and I was rubbing the crystal using polywatch really hard using the cloth that came with the polywatch. Would never rub it that hard on a hesalite.

My PO have some scratch. I think the scratches is on the AR coating. I have tried to use polywatch, but it doesnt help.. When you are done and start seeing results, wipe off any residue from the crystal. You can do this with a clean cloth. I believe that AR coatings are only applied to the inside of the watch crystal. If this is the case, then the scratches you are seeing are not to the coating, but to the sapphire itself. Sapphire is incredibly hard to scratch (bravo for finding a way to scratch it), but that also means it is equally as hard to polish.No matter how careful you are, plastic watch glasses will scratch over time. This is mainly due to the position of the watch on the wrist, where it can easily scrape against a wall or other object. Unlike glasses, these scratches only detract from the beauty of the watch and not its function. However, it is annoying to constantly look at it. The product With the included polishing cloth, rub in a circular motion, with firm, constant pressure. The heat from the friction will allow the Polywatch to smooth out the crystal's surface. Usually I use masking tape around the bezel and edges to protect them. This is very important for gold-plated or filled watches as the chemicals tend to get underneath the plating and react with the base metal of the case.

The polishing process is the same no matter what you are polishing typically, so an acrylic crystal, metal, etc. makes no difference to what the process is on the most basic level - replacing larger scratches with progressively smaller scratches. When you are done, it will leave your acrylic or plexi crystal flawless and free of scratches, allowing perfect legibility onto the dial. The benefit of this is that you don’t have to replace your whole watch crystal in case it only has scratches. This is both a cheaper and more effective alternative.Polywatch® Glass Polish. High Tech Scratch Remover For Glass. Repair rather than replacing. Removes fine, light and medium deep scratches from watch glasses. Sufficient for approx. 30-40 applications. For use on cars, smartphones, watches, furniture, household, hobby, windows etc.

I apply Polywatch with a slightly damp cloth and rub in a circular manner. Works great on acrylic crystals and, with enough elbow grease, will even remove some fine scratches from mineral glass. old t-shirt .... moisten lightly with some finger's worth of water until it results in a "wet-spot" (insert dirty joke here) ... then a bit of the polish (fingernail sized drop) ... then I gently work the mustardy-paste into the wet spot until all the excess is in the fabric (about 2-3" across). As with all polishing, move through grits from coarse to fine, making sure that you remove all of the previous marks before moving on, and finished with Polywatch. Please excuse the dust... What I do is use microsandpaper, starting with 1800 grit and working to 12,000 grit, this allows me to remove virtually all the scracthes, as a final step, I use Polywatch. Polywatch is for removing fine scratches so the scratches have to be minor, or it's used as a final polish. Trying to remove large/deep scratches with it is not really the proper use. If the scratches are deep enough, you will just make them shiny rather then remove them. Using Polywatch on this for example, would be mostly useless:

Fair Prices

Polywatch is especially great for superficial hairline scratches as it doesn’t require a lot of grinding of the plastic material on the crystal. However, PolyWatch also works well for deeper scratches, although you need to apply more pressure and polish for a longer period of time. I'm curious about Polywatch, or any single product for that matter for a full crystal polish. I assumed that to get a good polish (ranging from scratch elimination all the way to a high shine), you need to progressively decrease the Plastic watch glasses scratch very easily and replacement is not always possible, particularly where the case is plastic. Polywatch slightly disolves and grinds down the surface of the plastic watchglass to smooth the edges of the scratch and fill the gaps with dissolved material.