276°
Posted 20 hours ago

Silverline Water Level 10m (633586)

£8.385£16.77Clearance
ZTS2023's avatar
Shared by
ZTS2023
Joined in 2023
82
63

About this deal

Toolty Water Level Gauge Kit is used for leveling points that are far apart. Measuring tubes with a readable scale are made out of durable plastic (PVC). Tight plugs prevent the outflow of water at the place of measurements. A water level is exactly what it sounds, it’s a form of level that utilises a principle of physics that water will always find its own level wherever it is placed. Tip water onto an uneven floor and it will always find the low spots for you. The job of marking is best done between 2 people so that both ends can be marked, so bear this in mind. Making sure things are level before they are fixed is an essential job for both DIY’ers and trade professionals alike and normally this is done using a spirit or laser level. A complete leak detection kit to help protect a basement area or other vulnerable area in the home such as laundry rooms, central heating systems or other water pipes, from unexpected water leaks. Including a LeakStop alarm panel, connection cables, 3 metre sensor tape and optional shutoff valve (sizes available between 1/2″ and 2″).

To save the job of making your own, you can actually buy a pre-made water level from most DIY stores such as the one below. However it is likely that it will cost a bit more than making one yourself. Fresh water and waste tank level kit from CBE consisting of a tank test panel with coloured LED indicators, tank probes and wiring harness. This kit is ideal if you are retro-fitting a water tank or if you don’t have a level monitoring facility as part of your 12V control system. The LEDs light up when the test button is pressed and indicate FULL, 2/3, 1/3 and RESERVE. Step 5 – Mark Level Points – Before you start marking, the fluid in the pipe will not be flat, it will be concave as in the image below. You should agree with your help whether you are marking at the low point of the concave or the high point Hold the hose ends at the same height. Allow the water level to equilibrate freely. Mark both levels of the surface of water on the hose.

Documentation

Before you can actually start levelling items with your water level you will first have to make it, if you’re not buying one. Follow the steps below to do so: Fill the hose with water almost completely (leave columns of air about 5-10 cm long at the hose ends), while trying to prevent air bubbles from entering the hose. Step 3 – Fill Tube – Using a second pair of hands, have them hold both ends of the tube upright. Take the funnel and push it into one end of the tube and then pour the water from the container to fill it. Don’t fill all the way to the top, leave roughly 2 – 3 inches at either end. Once filled, hold them up together and they should both be at the same level Step 2 – Hold to Second Object – Holding your finger over the top of the tube, take the other end down to the object where you need to mark a level and hold in a "near enough" position towards the top of the object

The only issues arise when external influences such as wind and the similar come into play as this causes water to move and thus upsets any levels. Tools and Products Needed for a Water Level Fresh water tank probe is supplied with a gasket and mounting nut for fitting to a 60mm diameter hole in your water tank and the wiring harness connecting the probe to the test panel is 4m long. Our collections by our couriers are happening as usual. As it stands, delivery times are not being affected too much. Please be aware though that Royal Mail and other couriers are sometimes prioritising essential items so please bear with us if your delivery takes slightly longer than expected.But what if you need to level items such as fence posts over a long distance, or indeed around corners, obstacles or other structures. If you don’t have funds for an expensive laser level or tool that can do this this is where the water level comes into its own. Read on to find out about this fantastic tool. What is a Water Level? Put on the end plugs. They will prevent an outflow of water to the place of measurements. After reaching the measurement levels, remove the plugs. Step 3 – Allow to Settle – Before any marking can take place, allow the water level to completely settle so remove your thumb or bung from the end of the tube and let it level off until there is no movement at all

The tube is then filled with water, except for a few inches at either end and they will both settle at the same level regardless of how close or far they are apart.Note: If using with tanks of a shallower depth than 400mm, the probe can be cut down to suit as follows: Some insurance companies now offer discounts to those whos homes have water leak detection installed, particularly when insurance claims have been submitted for water damage before, so it’s worth mentioning to your insurance company if you have one fitted. Step 4 – Move to Level – Once it is settled you have achieved a level point between both ends of the tube, you can then move it up or down until the fluid meets the height required. The other end of the pipe will be at the same height. You can then place your mark Step 2 – Prepare Water – Fill A suitable sized jug with water and add several drops of food colouring to to dye it. This will help to make it more visible in the tube

Yes, you can continue to return items as normal as long as you follow the government guidelines about leaving your house.

Feature Highlights

In case of water loss, refill and adjust the device. Colours on images on different devices may vary. We cannot guarantee an exact match of the colour to the product.

Asda Great Deal

Free UK shipping. 15 day free returns.
Community Updates
*So you can easily identify outgoing links on our site, we've marked them with an "*" symbol. Links on our site are monetised, but this never affects which deals get posted. Find more info in our FAQs and About Us page.
New Comment