Conductive Wire Glue/Paint - NO Soldering Iron

Product Information

Henkel’s LOCTITE® range of conductive adhesive for electronics offer strong component and PCB interconnections for on-demand, long-term, and reliable performance. Our broad portfolio of electrically conductive pastes is formulated using a variety of base chemistries including acrylate, epoxy, and silicone platforms, each of which is designed to provide manufacturers with choice and flexibility for varying requirements. Electrically conductive adhesives are used in SEM to fix and ground the sample to avoid electrostatic charging of the surface. Certain temperature-sensitive electronic components cannot be soldered because the intense heat of liquid solder and the soldering iron can cause damage to the component. This type of application calls for an electrically conductive adhesive that can be used instead of solder. PCBs with components attached to both sides can also benefit from using an electrically conductive adhesive as the assembly process is easier without the risk of components dropping off the underside when parts are soldered on the top. When using electrically conductive adhesive for an entire electrical assembly, it negates the requirement to undergo a solder re-flow process. Recently our quality engineers at EPR rejected a PCB after its standard soldering process. The reason: a bad soldered component (TDK Capacitor 150pF CGA3E2C0G1H151J080AD). After analysis it was clear that this particular part should be used for conductive epoxy glue instead of the standard soldering process, because it had AgPd plating on its terminals. What is conductive epoxy? A cookie set by YouTube to measure bandwidth that determines whether the user gets the new or old player interface.

An unfilled epoxy with independent heat-curing (60 minutes at 80°C) and light-curing (2 - 6 seconds at 60 mW/cm2) mechanisms. Complies with ESA (ECSS-Q-70 02) and NASA (ASTM E 595-93) outgassing requirements. Silver-filled polyurethane adhesives are starting to appear on the market. They are two-part adhesives, so they either require mixing or they are supplied pre-mixed and frozen like the snap-cure epoxies. They offer high peel strength and flexibility. As they are silver filled, high levels of conductivity can be achieved (around 0.0001 Ohms∙cm to 0.0004 Ohms∙cm). Electrically conductive adhesives can be used to paint the inner surface of plastic boxes containing electronic devices. This makes a Faraday cage saving the internal components from electromagnetic radiation.This pertains to electrically insulating adhesive i.e. the electricity must not be conducted. Many potting and encapsulation applications require an epoxy glue with high dielectric strength. A high viscosity unfilled epoxy with independent heat-curing (60 minutes at 80°C) and light-curing (2 - 6 seconds at 60 mW/cm2) mechanisms. Very high Tg of 185°C. When there is a requirement for bonding large areas or joining complex parts, thermal adhesive films are the preferred materials. Larger bonding areas are problematic for liquid-based mediums as voids may result.

As previously mentioned, copper tape can be incorporated into a selection of different crafts and DIY projects. This can include stained glass artwork and wall art, as explored above, but it can also include a wide range of innovative craft ideas. Because this glue is quite flexible and you can vary its resistance, it has potential for different kinds of paint on sensors for robots or other devices. It should be possible to paint on strain gauges on the outside of a regular glove and use it for virtual reality or other control possibilities. Touch sensors and membrane switches can be painted on various flexible or rigid surfaces.The strain gauge or a glued resistor can also be used as a temperature sensor. If it is taken from the shade into the full sun, the resistance increases. So, it could be used to measure the difference between room temperature and overheating conditions. The BOND PLY family of adhesives is both thermally conductive and electrically isolating. BOND PLY materials, available in PSA or laminating formats, provide for the decoupling of bonded materials with mismatched coefficients of thermal expansion. BOND PLY offers: Looking Conductive Adhesives, then you have reached the right place. These adhesives are electrically conductive and are formulated from silicone or epoxy resin filled with metallics or conductive carbon fragments. Conductive adhesives are a liquid solution that can be applied to create a thin and flexible layer of highly electrical conductive material to an area or device. Our range of conductive adhesives are sourced from leading brands such as; 3M, Chemtronics, Electrolube, MG Chemicals and RS RPO. How do they work?