Joined in 2023 
82 
63 About this deal
Make sure they are secured in place but not too tight! If installed too securely, it can prevent thermal expansion and contraction, meaning the installation can have all sorts of problems. Install the sheets with the ribs running in the direction of the slop. Clamp at least one rib in place in the glazing system. Whichever method you choose, ensure the polycarbonate sheets are cut into small, manageable lengths (around 700mm wide). Using multiple sheets can make for a more secure fitting. What’s more, cutting the sheet into smaller sizes can make reaching over the roof easier when it comes to snapping the sheets in place on the glazing bar. Inspect the tiling battens to make sure they aren’t rotting or damaged. If they are, you could fit a batten strip along the verge. To ensure that your new dry verge matches the appearance of your current roof tiles, we supply dry verge systems in a wide variety of colours and finishes. So no matter the finish you’re looking for, your dry verge will provide a clean, attractive finish that blends in perfectly with your home. Benefits of A Dry Verge System
If required, install the underlay and ensure that the battens extend beyond the gable wall evenly by between 20 and 40 millimetres. This step is usually the most difficult – forcing up the glazing bar cap. You will have to be very careful during this stage. With your screwdriver or special glazing bar cap removal tool, cautiously remove the plastic cap apart from where it is joined to the toothed aluminium glazing bar; making sure you hold the polycarbonate panels in place. Step four: You’ve got your project plan in mind for your ideal polycarbonate roofing systems in place. Now, to find out what polycarbonate roofing sheet is best for your project. Here are some of the advantages you can see when it comes to different types of polycarbonate roofing: Product type Position the second verge unit so it can clip or slot into the first, nailing the top of this second unit onto the batten end clip.We also provide individual dry verge units which provide many of the same benefits as continuous systems. These individual units offer the same reliability, durability, easy installation and low maintenance across their lifespan. The key difference is that rather than fitting along the entire verge as a single, continuous unit, individual dry verge systems are sectional, designed for one course of tiles. Have More Questions About Our Dry Verge Systems? A roof verge is the part of the roof where the tiles end, where the roof meets the gable. Traditionally, a roof verge is fixed with mortar to create a waterproof and weatherproof finish. Note: Make sure that there is a 5° slope when fitting the sheets – this will allow rainwater runoff. Position the second verge unit in the slots of the first one (if the product features slots). If working on a “flex” dry verge system, ply the verge unit open and push it onto the tail of the first verge unit, ensuring the end of the verge lines up with the end of the tail, and nail the top into the batten end clip. Step 7:
The second method, if you choose to cut across the grooves, is to cut using a fine-tooth circular saw or handsaw. We work with a number of leading manufacturers to offer our customers with a brilliant range of dry verge systems. These include dry verge caps and units from brands such as Envirotile, Tapco, Britmet and Ariel Plastics. Each of these manufacturers is renowned for their commitment to quality and continuing innovation. Thanks to their use of modern UPVC and GRP plastics, their products for dry verges are both incredibly reliable and lightweight, making them simple to install for homeowners and tradespeople alike. You can retro-fit our dry verge products to any property to improve the look of your roofline. With a clean-edge design, they make improving the appearance of your home effortless, while offering outstanding protection.
Buying cut-to-size sheets can make your life much easier! With pre-cut polycarbonate roofing sheets, you can install the product as soon as possible. You can also benefit from not having to deal with the mess after cutting the sheets. Use our cut-to-size service to have polycarbonate roof sheets cut to your requirements. When sealing polycarbonate roofing sheets, apply suitable tapes, closures and sealants to prevent the ingress of moisture dust and insects – blanking tapes are to be applied to the top and breather tape is to be applied to the bottom end of the sheet. The breather allows air to move through the space freely; thereby reducing the chance of condensation. Fix the batten end clips to the end of each batten. This will create a secure place on which you can fix the verge units. Step 3: The first method can be done with a sharp knife tool, cutting in the same direction the grooves go rather than across. Note: As you drill the sheet, make sure it’s supported securely underneath via the H profile and don’t drill within 4mm of the edge of the sheet.
As well as lifting the look of your roofline , our Eaves Protector and Ridge Caps are ultra - low maintenance. They are manufactured from high-quality UPVC, a material favoured for external property projects. They outperform wet verge products and add a clean finish to any roofline. Just how simple they are for anyone to install, whether they’re a professional or a handy homeowner is one of the many benefits of dry verge systems. Of course, each system will be slightly different so you should always follow instructions from the manufacturer, but below you’ll find a handy guide outlining the main steps. Install the underlay if required, and ensure all battens extend beyond the gable wall or bargeboard by 20-40mm – they must extend by the same distance to create a straight and even line. If the tiling battens are rotting or showing signs of wear and tear, the alternative is to fix a batten strip along the verge instead. Step 2: Remove the glazing bar end caps. These are typically foun d covering the glazing bars and fixed by a screw. Remove the screw and the end cap should reveal the inside of the glazing bar/glazing bar cap combination. Step three: In some cases, the verge units are suitable for both left and right-handed verges – if this is the case, just remove the tab to make the verge suitable for the side you are working on. If not, just ensure you have the correct verge unit for the side you are working on.The ideal time you can expect it to last is a minimum of 10 years! However, do not put heavy weight on it. Polycarbonate roofing is not designed to support heavy weights, including that of a person. Please note: we compare our dry verge product prices against competitors’ every day of the week . Our Price Promise Guarantee is a market leader. If you find the same product cheaper online , we promise to match that price. We take our commitment to low prices seriously and always aim to sell our products at the lowest available price.
Great Deal 
New Comment