UA Volt 476P USB Audio Interface for recording, podcasting, and streaming

Product Information

A microphone is typically connected with an XLR connector, and an instrument or line level signal is connected with a ¼” (6.35 mm) TS or TRS plug. Please note: IOS requires external Volt power supply and an Apple Lightning to USB Camera Adapter (except iPad Pro with USB-C). Features Note: For software that only recognizes a stereo input, the signal from Input 1 is duplicated to Input 2.

Press the button repeatedly to cycle through the presets or disable the circuit (VOC, GTR, or FAST). Press these buttons to toggle the Vintage Preamps. The Vintage Preamps can be used on mic, line, and instrument inputs. Volt 476P can be combined with an iPad or iPhone to create a powerful and portable mobile recording rig. Whether you’re capturing ideas on the go or recording your band’s practice sessions, the Volt 476P is ready to go. To use Volt 476P with your compatible iOS device, you need to use the included Volt power supply and an Apple Lightning to USB Camera Adapter (iPhone and non-USB-C iPads). Free Software Suite Now, about those Vintage and 76 Compressor buttons. It’s common for companies with high-end product lines to include some of their fancy tech in their consumer-grade offerings. Universal Audio give you two such extras, Vintage emulation on the microphone preamps and 1176-style analogue compression.Increase the buffer size setting in the software on your computer. When recording, you can use direct monitoring to record without latency at higher buffer sizes. Vintage Mic Preamp mode for recording your voice or guitar with the rich, full sound of an iconic UA tube preamp The output meters show the level of signal at the monitor and headphone outputs.The red LED lights to indicate that the level is near 0 dB. (15) Host indicator To learn how to set up Volt with recording software and how to redeem your bundled software, please see UA Connect with Volt Interfaces.

The indicators above the 76 Compressor button indicate whether the compressor is off or enabled on one of the presets. The 76 Compressor presets have the following characteristics:The sources that you hear in the monitor and headphone outputs are assigned using the Monitor Source buttons (11). To hear your computer or software in the monitor speakers and headphones, Monitor Source OUT 1-2 must be enabled. These outputs are enabled by default. Connect Volt to a USB 2.0 (or higher) port on your computer with a USB-C to USB-A cable (included), or with another cable. Phantom power is required by most condenser microphones, but is usually not required with dynamic microphones or ribbon microphones (phantom power can damage some ribbon microphones).

Connect Volt to your system using the included USB-A to USB-C cable, or another cable appropriate to your system, and power on Volt. Vintage Mic Preamp mode lets you record voice or guitar with the rich, full sound of a classic UA tube preamp When any combination of both IN and OUT sources are enabled, the volume from your audio software is slightly reduced so you can clearly hear your input signals.The Vintage Preamp adds a carefully crafted analog tube preamp emulation, inspired by Universal Audio’s all-tube 610 console preamplifier, to the sound. When the button is lit orange, the circuit is active.

Use TRS (balanced) audio cables for the best results with balanced audio sources. Balanced equipment uses three conductor wiring (via TRS or XLR connectors) to reduce interference and electrical noise, and to provide better audio quality over longer cable runs. Use TS (unbalanced) cables for instruments that are not balanced, such as an electric guitar or bass, or an unbalanced synth or sound module. TS connections may also be suitable for shorter input cables, where electrical interference noise may not be an issue. Your system sounds will now play through Volt, and the first input on Volt will be the default audio source. Set up Volt for audio software I/O on macOS Tip: The Buffer Settings panel shows the input and output latency in the ASIO Status area as you change buffer sizes. This cookie stores user-like settings for the chat system provider, which are required for our online chat service. Trusted Shops

Harness an exciting recreation of the legendary Universal Audio 610 tube preamp with the intuitiveintegrated tube emulation circuitry. The original preamp was used to during recording sessions for Van Halen, Ray Charles and more - and now you can use UA's exclusive Vintage Mic Preamp mode to capture the same professional sound! 76 Compressor Press these buttons to toggle the impedance and gain of the line inputs to accommodate Hi-Z instruments, such as electric guitar or bass. These buttons are lit green when the Hi-Z inputs are enabled. Your system sounds will now play through Volt, and the first input on Volt will be the default audio source.