Joined in 2023 
82 
63 About this deal
In soft ground applications, a ratio (by weight) of 6.6 water : 1 cement : 0.4 Bentonite is a good option which will provide a 28 day compressive strength of about 25kPa Today, I like to welcome Kim from The Best Ideas for Kids who is sharing a gorgoeus DIY Clay Leaf Magnet craft with us today. Not only do we LOVE to work with clay (we have many great easy clay projects for kids here), but these make stunning Autumn decorations, great little gifts for kids to make or would also be brilliant for decorating the Thanksgiving table (then let your guests each take one home at the end of their visit..). Over to Kim! Three types available – 33mm OD x 25mm (1”) ID, 42mm x 38mm (1¼”) ID with flush threads or 70mm flush coupled QJ inclinometer casing. GXM-100T– 6 leaf spider magnetic targets positioned on the outside of 33mm (1”) flush jointed access casing together with telescopic joints to accommodate higher settlements than the GXM100 GXM-200C –for large fill projects such as earth fill dams where cross arm magnetic targets are used which extend into the fill area by up to 2 metres thus providing a more representative sample of the fill material.
GXM-200PT– 6 leaf spider magnetic targets positioned on the outside of a flush jointed inclinometer casing together with telescopic joints to accommodate higher settlements than the GXM200. It is very important that each target is labelled and given a unique identification. Where 6 leaf spiders are used the pull ropes should also be labelled.That’s it! Kids will love helping you press the cookie cutters in and painting these will be fun too! We hope you enjoy the finished pieces. Feel free to choose any colors or cookie cutters too – the options are endless! And if you’re looking for another fun project to do with these cookie cutters – see our fall potato stamps we made with similar cookie cutters. Edison advised, “There's a way to do it better—find it.” We did; we created a way to remove leaves from lawns without an engine or motor that is so efficient it can outperform leaf blowers, sweepers, and even tractors pulling powered lawn vacuums. We can do it without pollution, dust, vibration, or noise: our method is quieter than raking. Noise isn't just an annoyance: researchers found that it adversely affects physical and mental health as well as increasing the risk of dementia. are virtually silent (the primary noise generated comes not from the machine but a slight sound from leaves as the Leaf Magnet™ gathers them) Mowers are OK if you have few leaves and lots of time. Rakes also move each leaf over and over again, creating blisters and sore muscles faster than clearing yards. In a hard clay a ratio (by weight) of 2.5 water: 1 cement : 0.3 Bentonite is a good option which provides a 28 day compressive strength of about 690kPa.
Using your leaf cookie cutters press into the clay. Be sure to use cookie cutters that have a design in the center of them so they create an impression when pressed into the clay. Then remove the cookie cutter and the excess clay around the cookie cutters. Greetings everyone! It’s Kim from The Best Ideas for Kids and I’m excited to be sharing with you today these beautiful fall clay magnets. Fall is my favorite season – especially when the leaves start changing colour. But not only that, fall brings on the start of a new school year, fun activities like going to the pumpkin patch and then looking forward to Halloween, Thanksgiving and Christmas! So today I’m sharing with you how to make these pretty air-dry clay fridge magnets. You won’t believe how easy they are to make. Kids will love helping or creating these on their own! And the best part about them is they look great on the fridge and will bring some fall décor to your kitchen. If it is not possible to have the datum magnet in stable ground, it is VITAL that the top of the access tube should be surveyed each time the instrument is read.Used which extend into the fill area by up to 2 metres thus providing a more representative sample of the fill material. For borehole installations the magnetic targets are located in position by means of leaf spring legs attached to the targets which are known as “Spider Magnets” and are available in either three or six leaf versions. GXM-200P– 3 or 6 leaf spider magnetic targets positioned on the outside of flush jointed inclinometer casing for installation in a borehole prior to fill after which a series of settlement plates and telescopic joints are added. Leaf Spider Magnets are the easiest to install as they can simply be placed on the outside of the access tubing and pushed down to the required depth using a special installation tool or lengths of piezometer pipe. For both the manual and automated systems Magnetic Extensometers are supplied in various configurations of the access casing, spider, plate and datum magnets to suit varying installation environments and techniques. The ones supplied by Geosense are listed in the table below:
Great Deal 
New Comment