Bosch Professional 100 ml Grease Tube (for SDS plus & SDS max Drill Bits / Chisels, Accessories for Rotary Hammers)

Product Information

Good adhesion – continuous lubrication and reduced consumption as film stays between lubricated surfaces. Autumn Statement: Workers to pay less in national insurance – but rate cuts don't offset the freezing of personal tax thresholds

So what’s the main cause behind shank breakages and how can they be prevented? We worked with our Technical Department to find out more. So, what is the difference between both of them? A max SDS drill is bigger than a regular SDS drill, and as such, it can drill bigger holes, it can chisel tiles, and it can break concrete faster. What is an SDS Drill Used For? As you would expect, SDS drills are more expensive than Hammer drills because they handle tougher tasks. Can You Convert a Normal Drill to SDS? After nearly 45 years of manufacturing SDS Plus products at our Sheffield HQ, we’ve seen a few shank breakages in our time…. But the majority of these could have been prevented.Most power tool manufacturers distribute grease specifically aimed at SDS shank lubrication and some power tools are even supplied with it. Martin Lewis: What the Autumn Statement means for you – including wages, benefits, pensions, ISAs, national insurance and more Apply some grease to the base of a drill bit before you insert the bit into the hammer drill. Step 2 : The tool is used for drilling holes into masonry, breaking concrete, and chiseling tiles. That’s why it often comes with three modes – Hammer drill, hammer, and drill modes. When you select the hammer drill mode, the drill bit spins and also hammers the surface at the same time. That’s why it is able to drill holes faster.

When you select the drill mode, it spins only. The hammer mode is meant for breaking concrete only. It is used to break concrete during demolition. You need the right drill bit for different tasks. The SDS hammer drill is specifically created for hard tasks. How Do You Grease an SDS Hammer Drill? 4 Steps NatWest, RBS and Ulster Bank to close at least 172 branches in 2023/24 – here's the full list, plus alternatives Both employees and self-employed workers will pay less in National Insurance from next year, Chancellor Jeremy Hunt has announced in today's Autumn Statement.Specifically formulated for rubber to rubber lubrication where any effects such as hardening or swelling of the rubber must be avoided. It therefore can be used on automotive hydraulic brake and clutch components where compatibility with natural rubber and SBR seals are involved. It may also be used to assist the assembly of natural and synthetic rubber components for automotive brakes or clutch systems and suspension units. Examples of high temperature grease suitable for SDS Plus shanks include Lithium grease and Molybdenum Disulphide. Excellent EP and anti-wear properties – protects equipment against extreme loading and helps minimise bearing component wear.

Your workshop isn’t complete without an SDS drill because of the usefulness of the tool. And you should not just choose any SDS drill at random. It is better to follow the tips below. Multipurpose extreme pressure greases displaying both high melting point and water resistant characteristics. Suitable for plain roller and ball bearings and chassis lubrication. General automotive, industrial and marine applications. These greases have been formulated with additives that provide good film strength under medium to high loads. Also suitable for chassis lubrication. Molywhite and Vigo do not have a specified shelf life, but they recommend it to be used within 1 year. Place the tip of the bit on the spot where you want to begin breaking, then trigger the drill. Step 6 :We want you to get the best possible performance out of your tools, so we’ve put together some tips to maximise your SDS Plus accessory’s life and help prevent overheating and frustrating shank breakages. The main cause of failures in SDS Plus accessories is overheating of the shank. SDS Plus products are more prone to this than other types of shanks due to the unique workings of an SDS machine. The hammer action is created by a piston moving up and down inside the nosepiece of the machine. This in turn causes the accessory to move up and down creating friction, and friction causes heat. When there is too much localised heat, temper embrittlement occurs causing an irreversible change to the structure of the steel, causing it to fracture.

Dismantle the hammer drill and grease all the internal parts where two or more metals are rubbing against each other. Step 4 : If longer periods of use are required, an option is to obtain additional accessories and alternate their use. Martin Lewis: What the Autumn Statement means for you – including wages, benefits, pensions, ISAs, housing, national insurance and more Although breaking concrete is a tough task, it can be very easy when done with an SDS drill. Here are the steps involved. Step 1 : An SDS Plus shank is only 10mm in diameter. By the time the necessary grooves have been machined, the cross-sectional area of the steel at its smallest point is approximately half that. Therefore, without employing due care, heat build-up can be rapid because of the relatively small cross-sectional area at that point.”

Can You Convert a Normal Drill to SDS?

Always apply a small amount of lubricating grease to the grooved section of the SDS Plus shank before and at intervals during use. How often you use your SDS hammer drill will determine how often you grease it. What is the Difference Between an SDS Drill and a Hammer Drill? The Chancellor Jeremy Hunt has today (Wednesday 22 November) announced a range of tax, benefits and savings measures. We round up the key announcements and what they mean for you.