1.5mm Y00 Tri-Point Triwing Precision Magnetic Screwdriver for Switch and JoyCon Repair Opening Tool

Product Information

To go further, you’ll need to remove the fan. This fan is secured by three small screws. Again, tweezers or a magnetic screwdriver are helpful here. Make sure not to apply too much force when reinstalling the fan. Over-torquing the screws can damage the rubber anti-vibration mounts. UPDATE: after finally finding a proper Y000 driver at a local electronics store I was able to complete a repair on an Apple Watch series 3. While I did have some success filing down a cheap tri-wing driver until it fit the screws, there was one screw that it wouldn't loosen. The bottom line is this: Remember though, don’t keep trying bits that don’t grab right away. every attempt that fails to turn it will take a little more metal from the screw. For drivers, you get a Y00 tri-wing driver and Y2.0 driver. These are sufficient for disassembling both the switch and the JoyCon controllers. There’s also a small Phillips driver to go along with them. All three drivers have a sturdy green plastic grip, with an ergonomic hourglass profile. The bases rotate, which makes them easy to hold in place while you’re working. The driver tips are constructed from industrial-grade steel for durability and long life.

Inside, you’ll see a stainless steel shield that covers all the internal components. This shield serves as both a dust guard and a heat protector. The shield snaps into the front edge of the Switch. You can either remove the tabs with a nylon spudger, or use a small flathead screwdriver if you’re feeling brave. Beneath the shield, you’ll see that the microSD drive is easily replaceable. If the tool is advertised as one that's made for Apple products then it's probably going to work fine provided it's from a reputable tool maker. Get a proper Y000 driver, don't use Y00 as someone suggested. Don't use hot glue. Rubber bands do sometimes work but they won't in this case because the screw is too small and the driver will poke right through the rubber band with the application of any pressure.The YOOWA Nintendo Switch Triwing Screwdriver Set is the most barebones of all. But barebones isn’t the same thing as low quality. The drivers aren’t plastic. They’re constructed from durable stainless steel, with a colorful anodized finish that’s easy on the eyes. The tips are hardened, which means they won’t strip even after several uses. The drivers are Philips PH00 and Triwing Y00 respectively, just what you need for your Switch. And both include YOOWA’s lifetime warranty. Get yourself a plastic pry-bar, and you’re good to go. Final Verdict One part that isn’t easily replaceable is the battery. It’s not designed to be replaced by users; instead, Nintendo offers a paid replacement program. For safety purposes, you want to disconnect the battery before performing any other repairs. It connects to the rest of the unit with a four-pin plug. This plug can be removed by hand, but it’s relatively small, and a pair of tweezers makes it easier. If you want to access other parts, you’ll need to pry the battery loose from its adhesive. Do this gently and carefully with a plastic pry tool. Otherwise, you might inadvertently damage it. Removing and replacing the USB Type-C port is a bit complex. You’ll need some soldering savvy if you want to do it yourself. On the other hand, the speakers are easy to remove. Once the motherboard is out, they simply pull free of their housing. That said, their wires connect through a tiny plastic connector. Unless you’ve got very small, dexterous fingers, you’re going to need some tweezers to work the plug free.

Another thing that makes the Switch easy to repair is that the digitizer is not fused to the display. In other words, you can replace either part individually. The digitizer is secured to the display with a simple double-sided adhesive strip. Be careful of the cable, though. It’s on the long edge of the display, and needs to be carefully disconnected. Otherwise, you’re liable to damage it. If you keep trying to drive a Y000 screw with a tool that doesn't grab well you'll strip the top of the screw and then you'll need to find a way to make a straight groove in the top which will allow you to remove the screw with a tiny slotted driver (flat head). There are a ton of problems that can arise as a result of this. Metal flakes can get lodged in between surface-mount components and do more damage to the device. Also you could slip and cause more damage. Etc. The Starko 8-piece Nintendo Switch Tool Kit is a simpler kit than the last. It’s only designed for the Nintendo Switch and JoyCon controller, not other systems. Still, it’s very well designed, and it has everything you need to perform repairs. Now, we’re going to look at three of the best tool sets for repairing your Nintendo Switch. First off, we’ll review the Keten 17-in-1 Triwing Screwdriver Tool Repair Kit. This kit doesn’t just work with the Switch. It can also be used to repair the Super Nintendo or original Xbox. Next, we’ll look at the Starko 8-piece Nintendo Switch Tool Kit. This is a more barebones kit, designed to repair the Nintendo Switch and JoyCon controllers only. Finally, we’ll review the YOOWA Nintendo Switch Triwing Screwdriver Set. This set consists of two screwdrivers only, but can still get you most of the way through a teardown. Which set is best? Let’s take a closer look, and find out! Nintendo Switch Disassembly Basics

2 Answers

This is one of those things that requires a little bit of money to be spent because the tool manufacturing process and material used both need to be top-notch. A brief glance at the Keten 17-in-1 Triwing Screwdriver Tool Repair Kit reveals a large number of tools. Indeed, you’ll see several tools that aren’t necessary for repairing the Nintendo Switch. This is because it’s suitable for a variety of game systems, including the Super Nintendo and original Xbox. The Nintendo Switch is one of the most innovative game consoles ever designed. This is nothing new. In fact, it’s a continuation of Nintendo’s tradition of pushing the boundaries on console design. For another example, look no further than Nintendo’s last console, the Wii. The Wii offered motion-sensing control a full generation before the Xbox Kinect or the PlayStation SixAxis controller. With the Switch, Nintendo has offered a system that works as both a traditional console and a handheld console.

So, how do you actually disassemble a Nintendo Switch? It depends on what exactly you’re doing. For example, replacing the battery is relatively simple. On the other hand, replacing a blown speaker requires a full teardown. First, here’s a list of the tools you’re going to need: As you can see, each of these kits comes with its own advantages. To begin with, the Keten 17-in-1 Triwing Screwdriver Tool Repair Kit is an ideal choice for repairing multiple systems. You can use it to fix your Switch, your Super Nintendo, your original Xbox, or even your NES. The versatility is virtually unlimited.