Gunson 77111 Spark Plug Cleaner

Product Information

Don’t hold it too tight with the pliers, or you’ll damage the spark plug. Just let the plug sit in the pliers like a handle extension. Step 2: Use Gloves and Turn on the Torch Removing all the plug wires simultaneously will not confuse you when reinstalling them. When removing high tension wires, hold it on the low boot firmly and gently pull it out. If any of the cables prove stubborn to come out, hold it firmly and twist it a little to loosen up. Remember, I asked you to clean the spark plugs simultaneously. When a spark plug is cool, reinstall it and plug in the ignition coils or high tension wire before moving to another one. Continue this process until you clean all of them. Do not clean one and leave others. Method 3: Using Spark Plug Cleaner Tool Step 1: Disconnect the spark plug lead. Then, clean the area around the spark plug to avoid getting debris in the combustion chamber when you remove the plug. Type: The type of cleaner is very important. In general, there are two types of cleaners; the first one is using sand and abrasive materials to clean the spark plug applications. The other one is non-abrasive cleaners that do not use any sand or other kinds of things.

If dirt or debris falls into the spark plug holes while taking off the plugs, it could cause catastrophic damages. When blowing off the junk with canned or compressed air, ensure you wear eye protection. The ABN Pneumatic Spark Plug Cleaner is the perfect tool for any vehicle or machine with spark plugs. This pneumatic sand blaster cleaner kit removes carbon build-up, helps restore like-new performance, and prolongs the lifespan of your spark plugs. Whether you have a motorcycle, lawn mower, or another type of vehicle, this spark plug cleaning tool have you covered. The kit includes a spark plug cleaning unit, fabric bag, airbag clamp, and abrasive material with instructions. Things to Know Warning: The spark plug will turn from red hot to its normal color long before it has cooled enough to be able to touch. Step 5: Repeat the Process for Each Dirty Spark Plug Allow the spark plugs to cool before holding them with your fingers. The plugs need to be cool before using them. You must be careful when dealing with spark plugs and a blow torch; the spark plugs will return to their standard color long before it becomes cool. To avoid burning off your hand, allow each plug to stay for 5 minutes before trying to reinstall it. Ignoring these issues can lead to serious problems like engine damage and result in expensive repairs. 3. Can I Spray Carb Cleaner Inside the Spark Plug Hole?Using a spark plug cleaner is a relatively simple process. First, you'll need to remove the spark plug from your vehicle and insert it into the rubber grommet of the spark plug cleaner. You have to clean spark plug areas before taking off the plugs. However, cleaning a spark plug requires removing them to access the carbon buildup. Q: How do you lubricate spark plugs? Hold the plugs with pliers on the end the ignition coil connects to. Hold the plug firmly and don’t squeeze it to avoid causing damage to the plug. The plier should only act as an extension. A bench vice is a better alternative to pliers. Apart from gathering the equipment, you must perform 3 essential preparation steps before cleaning spark plugs:

Keep sandpapering the electrode until it looks like bare metal. It is advisable to put on eye protection while sanding. Sandpaper is one of the best spark plug cleaners in the market. It requires brushing off the carbon deposits on the plugs with a wire brush and soaking the plugs with vinegar or petrol for a few seconds. Method 2: Using Blow TorchAs for vehicles with a diesel engine, they don’t require a spark plug as they rely only on high compression to ignite the fuel/air mixture. It is important to keep spark plugs clean, considering that these tend to get dirty with use due to the carbon deposits they accumulate during engine operation.

In this article, we’ll discuss at length how to clean spark plugs using a blow torch, abrasives, and spark plug cleaner tools. However, it is essential to know when a spark plug goes bad. How To Clean Spark PlugsSolution — you can scrub the threads with a wire brush.When using a wire brush, ensure it’s an angle, so it moves in the same direction as the threads and removes all the dirt off the fouled spark plug. However, it’s best to opt for a spark plug replacement in most cases. That’s because an old spark plug won’t perform as well as a new spark plug. To understand if you have a fouled plug and need to replace it with a new plug, look for certain signs such as: To start, get a container where you will place your spark plugs. Once the components are in, pour soda until the spark plugs are submerged. Add a generous amount of salt for a better result. This method is quite time-consuming, depending on the carbon and rust build-up on the plugs, so it’s best to do this if you are not in a rush. Finish off by brushing the spark plugs with a wire brush. The spark plugs on modern cars and motorcycles rarely get fouled as the engines run so cleanly; the spark plug is generally considered a consumable item and large mileages can be attained (50,000 to 100,000 miles) before they need to be replaced. Thus there is no real need to clean them at any point.