276°
Posted 20 hours ago

Devcon 5 Minute Epoxy - High Strength

£9.9£99Clearance
ZTS2023's avatar
Shared by
ZTS2023
Joined in 2023
82
63

About this deal

Chemical cleaning with Devcon Fast Cleaner 2000 Spray/Cleaner Blend 300 should follow all abrasive preparation. This will help to remove all traces of sandblasting, grit, oil, grease, dust or other foreign substances. Proper surface preparation is essential to a successful application. The following procedures should be considered: Remove all paint, rust and grime from the surface by abrasive blasting or other mechanical techniques. Always try to make the repair as soon as possible after cleaning the substrate, to avoid oxidation or flash rusting. If this is not practical, a general application of FL-10 Primer will keep metal surfaces from flash rusting. ITW Devcon will replace any material found to be defective. As the storage, handling and application of this material is beyond our control we can accept no liability for the results obtained.

If surface is oily or greasy use Devcon Fast Cleaner 2000 Spray/Cleaner Blend 300 to degrease the surface. Mixing Plastic Steel Putty (A) is formulated to be a dense mix that can be applied easily to overhead and vertical surfaces without running or sagging. For the 500g and 1Kg kits, empty the Resin and hardener onto a mixing board and mix using a spatula. Do not mix in the containers. For the 10Kg kit, add the hardener to the resin and mix using a T shaped mixer or Jiffy ES mixer attached to a power drill. Fold the material by vigorously moving the mixer up and down until a uniform mix has been achieved. Once mixed, immediately spread out the mass of material onto a suitable area before use to avoid a rapid exotherm and associated reduction in potlife. The Devcon ® brand of maintenance and repair products effectively rebuild equipment to original specifications or prevent failures from occurring in a preventative maintenance program. These include the strongest epoxy and urethane coatings for metal repair, rubber repair, belt repair, corrosion repair and floor repair. The specially formulated epoxy coatings and filler also protect handling & storage equipment from continuous wear and abrasion.

Aeropoxy 300g

Metal that has been handling sea water or other salt solutions should be grit blasted and high pressure water blasted and left overnight to allow any salts in the metal to ‘sweat’ to the surface. Repeat blasting may be required to ‘sweat out’ all the soluble salts. A test for chloride contamination should be performed prior to any epoxy application. The maximum soluble salts left on the substrate should be no more than 40 p.p.m. (parts per million). Strong enough to fill gaps. Sets in 30 minutes, cures in 12-16 hours to a clear transparent finish. Excellent for jewellery. Aluminium repairs: Oxidation of aluminium surfaces will reduce the adhesion of an epoxy to a surface. This film must be removed before repairing the surface, by mechanical means such as grit-blasting or chemical means. Devcon® Titanium Putty & Devcon® Brushable Ceramic Coatings Repair & Protect Pressure Vessel from Corrosion Devcon® Flexane® Putty Repairs and Devweld 531 Provide Corrosion Protection to Petrochemical Holding Tank

Under cold working conditions, heating the repair area to 38ºC – 43º C immediately before applying any of Devcon’s Metal-filled Epoxies is recommended. This procedure dries off any moisture, contamination or solvents and assists the epoxy in achieving maximum adhesion to the substrate. Industrial strength two-part epoxy is designated for heavier items requiring an extra-high-strength bond. Works on metal, stones, ceramic, crystal, china and wood. Waterproof and resistant to most chemicals.Devcon® Wear Guard™ 300RTC High Chemical Resistance Coating Reduces Pump Repair Frequency at Platinum Mine

A shelf life of 3 years from date of manufacture can be expected when stored at room temperature (22ºC) in their original containers For complete safety and handling information, please refer to Material Safety Data Sheets (MSDS) prior to using this product. Application: Point the dispensing tip at the proper location for applying the glue or epoxy. To keep a steady flow, smoothly move the gun applicator over the surface while holding down the trigger.

Asda Great Deal

Free UK shipping. 15 day free returns.
Community Updates
*So you can easily identify outgoing links on our site, we've marked them with an "*" symbol. Links on our site are monetised, but this never affects which deals get posted. Find more info in our FAQs and About Us page.
New Comment