Assortment of Rubber Flat Washers a Pack of 13 Tap Washers, Set includes 3 UK sizes, 3 x 3/8", 5 x 1/2" and 5 x 3/4" fits most traditional taps, perfect for tap repairs or replacements

Product Information

O rings can be used for static seals (e.g. taps) or for dynamic applications (e.g. pistons). These torus-shaped rings may also be called toric joints. Ceramic assemblies are very commonly found on monobloc, or mixer taps, as well as so-called quarter-turn taps. The operating mechanism requires just a quarter of a single handle turn to start and stop the water flow, so they’re a lot easier to use for anyone with dexterity issues.

Sealing: Rubber washers provide effective sealing solutions, preventing leaks and can be used to create airtight and watertight connections. It is not necessary to measure the washer diameter, as it is normally the same as the tap thread size. There are two main sizes of tap washers, 3/4″ and 1/2″, with some minor variations. If you have a tap with separate hot and cold handles, you will need to measure each one to determine the correct washer size needed. The easiest way to do this is to use a set of vernier calipers. Consider the Tap Type and Age: Remember that the type and age of your tap can also influence the size of washer you need. Traditional taps and older taps often use larger washers, while mixer taps and newer models might use smaller ones. As a leading supplier of rubber washers in the UK, Vital Parts ensures a comprehensive range and supply of high-quality rubber components. Our commitment to quality is evident in the selection of rubber washers we offer, catering to the unique demands of various industries. With a specialist supply chain, we can deliver rubber washers in large quantities suitable for large industrial and commercial projects. While still satisfying bespoke sizing and requirements even for small projects. Bespoke and Custom Rubber Washers:Not all taps have their own isolation valve, so you might have to just switch off your main water supply instead. If you’re working on a hot water or mixer tap, make sure to turn your boiler or immersion heater off as well. Once you’ve isolated the tap from its water supply, turn the handle into the on position to let out any residual water. When the tap runs dry, you’re all good to go. Remove the Existing Washer: First, turn off the water supply to avoid a minor flood. Then, you'll need to dismantle the tap. This usually involves removing the handle and unscrewing the valve from the tap base. Once you've done this, you should be able to access and remove the washer. Even if you don’t consider yourself a DIY-savvy individual, changing a tap washer is well within your capabilities. All you need is a few basic tools and a spare half hour or so, and our simple, step-by-step guide will see you through. What Equipment Do I Need to Change A Bath Tap Washer? However, don't hesitate to call in a professional if you're unsure. It involves turning off the water supply, disassembling the tap to remove the old washer, fitting the new washer, and then reassembling the tap. Turn off Your Water Supply: Before you start, you'll need to turn off the water supply to your kitchen tap. This is usually done via the isolator valves located beneath the sink.

Look under the tap for an isolation valve to turn off the specific water supply, and if you can’t see one, switch off the water mains. Either way, open the tap to drain any water left in the pipes. If you’re working on a hot water tap, you’ll need to shut off the immersion heater and boiler too. Nylon is the most common material used to make tap washers. Its cheap, lightweight and easily manufacturable, as well as sturdy enough to resist the wear and tear of everyday use. The other materials all have their pros and cons, but they all serve the same purpose. They do all eventually degrade, which is why they need replacing every so often. As for size, tap washers can range from 9mm to 40mm in diameter, depending on the build of the tap itself.The standard DIN / ISO 1629 governs the classification and designations of these seals. The most common and widely sold O rings are made of NBR (Nitrile). Unscrew the Valve: Once the handle is off, you should see a brass spindle or valve. Using your adjustable spanner or wrench, unscrew this. Be careful to protect the finish of the tap with a cloth while doing this. Choosing the correct size washer for your kitchen tap is crucial for preventing leaks and ensuring a smooth operation. With the exception of plumbing washers, which are fairly easy to select, you will have to consider the following factors if you have to replace washers or O rings in another other type of installation: