STC-1000

Product Information

The XH-W219 thermostat module with its STM8S µC and I/O (sensor input, keys, double display, relay) can be re-programmed for automation tasks, and it's easy to work with.

We’re a team of passionate brewers & distillers who want to share our learnings with others – helping answer some of the questions we had to figure out the hard way! F3: Čas zpoždění kompresoru doba čekání po dosažení cílové teploty, pokud nastavíte 3 minuty, regulátor teploty čeká 3 minuty, po 3 minutách sepne relé.

The first thing that is needed is to upload the sketch Before the connections are made from the Arduino to the STC-1000, the sketch needs to be uploaded to the Arduino. It is important that connections are not made before this. An unknown program running on the Arduino could set the pins to the wrong state and short circuit the STC-1000. This could damage your STC-1000 and/or your Arduino. The price is a bit higher –The Elitech STC-1000 is about 5 usd more expensive than the generic version Mám koupenou tuto sadu, ale pořad badam kam zapojit ovládání tricestneho ventilu. Jde mi o to zapojit 3cv na topný systém . Elitech STC-1000 digital temperature controller thermostat is one of the most classic thermostats from the Elitech with automatic changeover between cooling and heating. It controls the temperature according to the temperature set value and the return difference. With temperature measurement, temperature display, temperature control, temperature calibration, sensor fault alarm, over-temperature range alarm, compressor protection delay functions. It also has the function of Fahrenheit and Celsius conversion.

The actual shape of the workpiece iscaptured on the machine using Starrag’sown 5-axis measuring cycles. F1: SET GOAL temperature : pusch SET button again and here see currently set temperature ,If you want to change it, press SET again with the up or down arrow (whether or not you want to increase or decrease the temperature). Remember SET + arrow If measured temperature temperature set-point, the controller stops heating and cooling indicator is off. F4:Temperature calibration:You can make the Stc-1000 very accurate, just compare the temperatures with a verified thermometer (best compare at the target temperature) you can increase or decrease the temperature after 0.1C steps. Once you’ve wired the controller, calibrate it. This is a straightforward process that involves immersing the heat probe in ice-cold water until it reaches a stable temperature.You'd need an Arduino board (like the Arduino UNO) and an STC-1000 thermostat with the proper hardware version (A400_P). The correct STC-1000 can be bought here. Když připojím Termostat do sítě, tak mám na „vstupu 1“ napětí, signálka ukazuje „topení“, ale na vstupech 5 a 6 mi zkoušečka (jednoduchá tužková do zásuvky) neukáže žádné napětí, tj. nesvítí doutnavka. Finally, program it to your preferred temperature value. Doing so ensures your wash or wort stays within the ideal range, so you don’t experience stalled or overactive fermentation. The controller allows you to regulate temperature with precision and consistency, which can help improve the quality of your product.

High pressure cooling for water-based coolants or oil (pressures up to 150 bar / 2175 psi to get as close to the cutting zone as possible) To set up the controller, you first have to wire it. You can do this by connecting the device to a few store-bought wires and a project enclosure. In the past, I made a review and manually for the generic OEM version of the STC-1000She had a good rating, and I have a good experience with her.The aim of the comparison between Elitech and the “Generic version” is to find out whether one is just a plain copy or Elitech has some added value. Distinguish the sensor lead, power cord and output relay interface. Do not connect wrong or overload the relay. Pod displejem jsou čtyři tlačítka, která ovládají termostat STC 1000. První tlačítko je zapnuto / vypnuto pod ním je tlačítko „SET“ a další dvě tlačítka se šipkami jsou + a – slouží k navigaci v menu ke zvyšování nebo snižování hodnot.The menu is the same as the OEM generic versionThe added value would be, for example, the ability to set the audible alarm as for STC2000 Process analyses and stability evaluations can be made easily with integrated sensors and evaluation routines.

STC-1000+ is an open source implementation of firmware(s) for the STC-1000 dual stage thermostat that add improvements and features over the version it is shipped with. It also provides an easy and cheap way of uploading said firmware(s) to the thermostat by emulating a programmer using the widely available Arduino platform. Finally the project adds a few tools that make it easier use and upload the firmware(s). Only when the sketch is uploaded correctly is it safe to make the connections to the STC-1000. Connect the STC-1000 Jde mi voda z aku nádrže do radiatorů, ale chtel to nastavit tak, ze když voda z aku vychladne na 35stupnu zavře se ventil a zamezí průtoku z aku nádrže a sepne se el kotel a poběží stávající okruh topné sestavy mimo aku nadrz .. nevím kam přesně zapojit el systém zavíráni 3cv STC1000 from Elitech had completely different PCBs with other components than the generic STC1000.Here’s a comparison on photos: Generic is left and Elitech is right The temperature controller helps regulate the temperature of your fermentation vessel so you don’t wind up with off-flavors or stalled fermentation.Firmware built to control a single vessel brew system (for example Braumeister, Grainfather and similar systems/DIY setups). Read more here STC-1000+ RH (relative humidity controller) firmware