Teltonika RUT950 LTE 4G Router

Product Information

Marketing material such as photos might need replacing. Cable management and integration procedures might need reviewing due to minor connector layout and visual changes Mode determines what options and configurations are shown. In Basic mode only the essential configurations are shown. In Advanced mode there is greater freedom to configure and access more options.

Hierbij verklaart TELTONIKA NETWORKS dat het toestel I RUT950 in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 2014/53/EU The Certificate Generation tab provides the possibility to generate TLS certificates required for secure authentication and communication encryption used by some of the devices services. L2TPv3 (Layer Two Tunneling Protocol Version 3) is a point-to-point layer two over IP tunnel. This means you can tunnel L2 protocols like Ethernet, Frame-relay, ATM, HDLC, PPP, etc. over an IP network.bit: INT, UINT; 16 bit: INT, UINT (MSB or LSB first); 32 bit float (Big endian, Big endian with byte-swapped, Little endian, Little endian with byte-swapped) TELTONIKA NETWORKS tímto prohlašuje, že RUT950 splňuje základní požadavky a všechna příslušná ustanoveni Směrnice 2014/53/EU Paired with secure and functional RutOS, plenty of processing power, and Teltonika Networks Remote Management System (RMS), this device offers unprecedented application flexibility to manage and control equipment remotely over LTE Cat 1. Draft EN 301 489-1 V2.2.0, Draft EN 301 489-17 V3.2.0, Draft EN 301 489-19 V2.1.0, Draft EN 301 489-52 V1.1.0 FCC 47 CFR Part 15B (2018), ANSI C63.4 (2014)

TLS encryption provided by Stunnel can be used as an additional layer of encryption for data sent by VPN. Status LEDs: 1 x bi-color connection status LED, 5 x connection strength LEDs, 4 x LAN status LEDs, 1 x Power LED Fixed Load Balancing, GRE, MQTT broker, IP alias, Operator list & SIM operator connection migration from legacy firmwares Defines two time intervals: the first is used to periodically send ICMP requests to the OpenVPN server, the second one defines a time window, which is used to restart the OpenVPN service if no ICMP response is received during the specified time slice. When this value is specifiied on the OpenVPN server, it overrides the 'keep alive' values set on client instances.Specify time amount in seconds between Keep Alive messages. By default this option is 0 which means it is disabled. Recommended value for a device behind NAT is 25. The Access Concentrator to connect to. ISPs used Access Concentrators to route their PPPoE connections. Usually, the settings are received automatically, however in some cases it is required to specify the name for an Access Concentrator. Leave empty to detect Access Concentrators automatically. Any external antenna gain must meet RF exposure and maximum radiated output power limits of the applicable rule section. Next, the Configuration Wizard will start to help you set up some of the router's main operational parameters.

Old firmware versions will not support new flash memory, meaning that only RUT9XX_R_00.06.02 and newer firmwares will work with updated hardware. Enabled - the device attempts to connect to RMS every 2-5 minutes (every 2 minutes the first hour; then every 5 minutes). If it cannot connect for 14 days, it will enter Standby mode. The Sign the certificate slider control whether the certificate will be signed automatically or manually after the generation is complete. Refer to the figure and table below for information on the fields contained in the Stunnel Globals section.

Arrange power and Ethernet cables so that they are not likely to be stepped on or have items placed on them. How long the keying channel of a connection (ISAKMP or IKE SA) should last before being renegotiated. The time is specified in seconds. The s, m, h and d suffixes explicitly define the units for seconds, minutes, hours and days, respectively. This device complies with the relevant FCC RF radiation exposure limit set forth for an uncontrolled environment. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter and must be installed to provide a separation distance of at least 20 cm from all persons.

Fixed IPsec tunnel creation issue when compatibility mode is used and the tunnel name contains an underscore TELTONIKA NETWORKS декларира, че RUT950 е в съответствие със съществените изисквания и другитеприложими разпоредби на Директива 2014/53/EU In the General section of Peer instance you can configure basic information about the endpoint to allow communications.By default the remote file system will be mounted on /sshmount, directory will be automatically created if does not exist yet. A Phone Group is a collection of phone numbers that can be used as the recipient in SMS & call related services instead of specifying every number individually. The phone group list is empty by default thus, you must first add at least one new group before you can add phone numbers to it. To create and begin editing a phone group, follow these steps: