PJRC DEV-13305 Teensy LC Development Board with Boot Loader and Micro USB for Arduino IDE and Write Arduino Sketches - Green

Product Information

many types of libraries to work well when used together. Direct Memory Access (DMA) Teensy 3.2 has a general purpose 16 channel DMA controller.

Teensy-LC provides a 5V output to directly drive WS2812/NeoPixel LEDs. A 74LV1T125 buffer is connected to pin 17, with the increased output voltage available on another pin. stand-alone to write your HEX file into Teensy's flash memory. Automatic Software Entry to Program Mode While developing with Teensy, loading normally happens automatically specialized DMA engines built in. Random Number Generator True random number hardware is capable of generating random display to use, due to superior software support. ST7735 Color TFT These displays are slightly smaller and lower resolution than ILI9341. The "Teensies" have also been used as a controller for existing keyboard matrices, such as, when a keyboard's protocol is deprecated and/or the keyboard has been cut down into a smaller matrix.

PIMORONI LTD.

Differential & Programming Gain Amplifiers Pins A10 & A11 and A12 & A13 have a differential amplifiers. Analog Comparators These comparators allow an analog signal to be converted to Many Arduino libraries require a hardware timer. Traditional Arduino products have 3 or 4 timers, with only 1 or 2 providing more than 8 bit resolution. Teensy-LC has a total of 7 timers, all of them with 16 or more bits of resolution, to allow excellent compatibility with easy-to-use libraries. Many combinations of popular libraries, which would normally conflict, can seamlessly run together on Teensy LC and Teensy 3.1. USB power (VUSB)– This is typically 5V supplied through the USB cable. A solder pad next to the USB connector also connects to the same VUSB power. An on-chip regulator provides 3.3V to power the CPU.

low versus high. Analog Outputs / Digital To Analog (DAC) One true analog output DAC is present on pins A14. void delayMicroseconds_WhileDiscardingInput ( unsigned int usec ) { elapsedMicros t = 0 ; while ( t < usec ) { usbMIDI . read ( ) ; // read and ignore incoming USB MIDI } } Transmit Speed and Message Rate Limiting select 74HC4051 channel 5 (of 0 to 7) digitalWrite ( 1 , HIGH ) ; digitalWrite ( 2 , LOW ) ; digitalWrite ( 3 , HIGH ) ; // allow 50 us for signals to stablize delayMicroseconds ( 50 ) ; // read the signals routed to pins 10, 19, 20 // through channel 5 of each 74HC4051 chip buttonPin10channel5 . update ( ) ; knobPin19channel5 = analogRead ( 19 ) ; knobPin20channel5 = analogRead ( 20 ) ; Teensy-LC delivers an impressive collection of capabilities to make modern electronic projects simpler. It features an ARM Cortex-M0+ processor at 48 MHz, 62K Flash, 8K RAM, 12 bit analog input & output, hardware Serial, SPI & I2C, USB, and a total of 27 I/O pins. Teensy 3.5 and 3.6 have a large number of pins, and are also pin-compatible with one-another. The Teensy 3.6 is not 5V-tolerant.steps, ranging from 150 ohms (weakest) up to about 21 ohms (strongest). Adjustable Output Bandwidth Digital output bandwidth is also programmable, in 4 steps: 50, 100, The processor on the Teensy also has access to the USB and can emulate any kind of USB device you need it to be, making it great for USB-MIDI and other HID projects. The 32 bit processor brings a few other features to the table as well, such as multiple channels of Direct Memory Access and an I2S digital audio interface! There are also 2 separate interval timers! Also, the Teensy LC can provide system voltage of 3.3V or 5V to other devices at up to 5-20mA. The Teensy LC can be powered one of 3 different ways, but it is important to note that these are mutually exclusive unlike typical Arduino boards. Internally the module does not provide any power switching between the different power inputs. In essence, if you hook up two different power inputs such as through the USB cable and also through the VIN pin, those two power sources will be shorted together. Teensy-LC will be ideal for inexpensive Internet Of Things projects when paired with a ESP8266 module, which requires a fast hardware serial or SPI port.