276°
Posted 20 hours ago

SANSUN 2.4W LED MR11 Light Bulbs, Replacement for 12V 20W 35mm Halogens, Fiber Optics Christmas Tree Bulb, G4/GU4/GZ4 Bi-Pin Base, Soft White 3000K, (Pack of 4)

£9.9£99Clearance
ZTS2023's avatar
Shared by
ZTS2023
Joined in 2023
82
63

About this deal

At this point, it’s important to note that if it is a halogen transformer,this maximum load applies to halogen light bulbs only. For example, if you have a 40VA transformer for halogen bulbs, you should not install 40-watts worth of LED light bulbs. This would overload the fitting and potentially cause a safety issue. When replacing Halogen MR16 light bulbs with LED bulbs, it’s important to use LED bulbs of equivalent wattage to your existing halogen light bulbs. This will ensure that the transformer can still handle the load safely. I’m considering changing our existing spots in the house to LED which are MR16 50W halogen bulbs connected in a series of 3 to an Aurora AU-150 transformer rated 50-150VA. We’ve got quite a lot of these throughout the house and if possible I’d like to avoid replacing these (due to the cost) with an LED driver equivalent. Would the existing transformer work with cool white 4000K LEDs? WWe don’t use dimmer switches at the moment but it would be a nice option – we have double switches at the moment. The number 4 in the name indicates the center-to-center distance between two pins, which is 4mm in this type.

For example, if you have one 35W halogen installed in your kitchen, ensure you swap it for 35W equivalent LED. The actual wattage of the LED light bulb may vary, but the equivalent wattage must be the same as your current halogen bulbs. For example, you might find both 5W and 6W LED light bulbs that have an equivalent wattage of 35W; both of these would be fine to replace 35W halogen bulbs. The volt-ampere (VA) rating is the maximum load (in watts) that a transformer can safely carry. For example, a 40VA transformer can handle up to 40-watts of electrical equipment, while a 10-60VA one can carry between 10 and 60 watts worth. Installing low voltage LED light bulbs on a transformer designed for halogen lighting requires you to find the equivalent wattage ( see above) for the LED bulbs, so as not to overload the transformer. Saving money and the environment are the benefits of replacing halogen with a light emitting device. Is it worth replacing bulbs with LED? They are brighter and produce a negligible amount of heat as compared to them. Moreover, the average life of a G4 LED capsuleis 30000 hours, which is ten times more than the halogen bulb. They have no toxic chemicals like mercury or Barium, thus posing no threat to human health. If you have low voltage halogen light bulbs installed with a transformer, the first thing you need to do before replacing Halogen MR16 light bulbs with MR16 LED bulbs is to find the transformer’s maximum load. You should be able to find this on the body of the transformer itself, in the form of a ‘VA’ number. This VA number will either be fixed, or it will be a range (e.g. 10-60VA).

Heading 2

See also What is the LED equivalent of a 250 watt bulb? Can I swap halogen headlight bulbs for LED? Anyone know the answer to this ?……My lights are 12 volt……20 Watt max…….Halogen…With transformer….. There are 4 lights…… 20w bulb in each one……MR16….GU5.3…. 50mm wide by 45mm depth You would need a transformer to reduce the mains voltage down to 12 volts. There are two types of transformers available in the market. One is the electromagnetic transformer and the other is electronic. Electronic transformers are preferred due to their efficiency and low cost. #3 The compatibility

Most people will be able to recover the cost of a new light bulb within three months. Less trips to the store and up the ladder can be saved with the use of LEDs. It takes about 25,000 hours for them to finish. By comparison, compact fluorescents can last up to 8,000 hours. Can you switch from halogen to LED headlights? Also I presume a reasonably competent (non-qualified) person can do this (taking appropriate precautions of course inc. turning off the mains supply). As most LED bulbs have a much lower wattage, for example 5W – this falls below the minimum rating that the transformer is designed for (20W). Yes, that’s right. The maximum load that the transformer/driver can handle is what you should be looking for in your MR16 downlights. If you have 35W halogen downlights that are installed with 10 to 60VA transformers, we can replace them with a new set of lights. Can I put LED bulbs in halogen fittings? I am currently looking to replace the halogen MR16’s in my daughters room which are currently 12v 50w on individual transformers. Can I change these for 35w equivalent MR16’s or do they need to be 50w equivalents.If you’re replacing low voltage MR16 50W halogens that have low voltage 12V transformer, the first and obvious option is to replace it with something like an MR16LED. The retrofit lamps should work from your transformer. This can cause you to have to replace your transformer. Can I use 12V transformer for LED? You may run into problems with this transformer, as it is designed for use with Halogen light bulbs and therefore has a wattage range of 20W to 60W. The natural energy-saving properties of LED light bulbs means that they can offer the same brightness of a halogen equivalent, but using only a fraction of the power. A 5W LED spotlight, for example, can offer the same brightness of light as a 35W halogen spotlight.

A G4 LED capsuleis a low power device with a usual operating voltage of 12 volts DC. Some companies also manufacture G4 LEDs that operate on 12 Volts AC. While the mains voltage around the world is 220-240 volts, you cannot directly connect the G4 led with the main voltage. #2 The Right TransformerI currently have down lights with Osram decode 51s (12V 50W) halogen bulbs. Each light has a dimmable 60VA transformer connected. Could you please advise on a suitable replacement dimmable LED bulb? FAQ about 12V transformer and light emitting device compatibility. The cost of efficiency and extra power consumption are explored in the FAQ article. The ‘LED drivers’ are designed for DC light. What is the difference between halogen and LED? The recessed fittings need replacing, and a switch to LED would be sensible at the same time. But I don’t want to replace the transformer. It’s important to note that the headlights are not the same as the ones in the picture. There are a number of advantages over halogens. They consume less power, do not heat up as much, and take up less space. According to XenonPro, you can’t just replace a bulb with an assembly. Can I replace halogen downlights with LED? These numbers tell you the maximum wattage that the transformer can carry. For example, a 40VA transformer can handle up to a 40-watt halogen light bulb, while a 10-60VA one can carry between 10 and 60 watts worth of bulbs. Some transformers might just carry one individual light bulb, while others might be able to carry several lower wattage light bulbs in a series.

Do I need to swap the transformers for Led drivers, do the also act as a transformer?. Do I also need to replace the dimmer switches? i’ve tried replacing my warm led spotlights with brighter led spotlights but they flash on and then go super dim. Can you help explain why that might be?Spotlights are ‘directional’ bulbs that emit light in a focused beam. Halogen spotlights are a form of incandescent light bulb that use a tungsten filament and a mix of inert and halogen gases to produce light. The European Commission directive in September 2016 banned the manufacture of this type of power-hungry spotlights. So i have removed 50W halogens and replaced them with 5W LEDS which are equivalent to 50W halogens. They work fine but i am worried it will cause a fire so thats why I have asked. Bulbs that operate on a lower voltage than 230-240V must be used with a compatible transformer when installing on UK mains circuits. The transformer converts mains voltage to a lower voltage suitable for the bulbs, ensuring they function as designed and preventing damage to the bulbs and/or light fittings. I have 2 gu4 halogen bulbs in my fireplace. I’ve tried to replace with two led bulbs. When I install the new led bulbs they dont work. If I leave one led bulb in and install 1 halogen bulb in the led light lights up. The halogen bulb does not.

Asda Great Deal

Free UK shipping. 15 day free returns.
Community Updates
*So you can easily identify outgoing links on our site, we've marked them with an "*" symbol. Links on our site are monetised, but this never affects which deals get posted. Find more info in our FAQs and About Us page.
New Comment