TCP Smart Wi-Fi Single Gang Wall Switch, white,packaging may vary

Product Information

You can control your switch and see the on/off state from anywhere with an internet connection through your smart mobile phone App. For this guide, we’ve also included reset procedures for some of the most common smart switches. While this list isn’t comprehensive, your switch may have a similar reset procedure. For full details, you should always consult the documentation that came with your model. In some cases, resetting a Wi-Fi switch can result in the loss of automations. Before you begin the reset procedure, make sure to record these to re-establisher after the reset. The primary switch in the left Junction Box in Figure 3 powers the light and has the smart controller in it. It does not matter which switch you choose as the primary switch. But the primary switch will have the blue indicator light on it, so that might be a deciding factor for placement. Wiring the primary switch starts off exactly like the single smart switch, with one additional step for the traveler wire. Here are the step-by-step instructions for wiring the primary switch:

Reconnect a Smart Light Switch that Has Lost - MUO How to Reconnect a Smart Light Switch that Has Lost - MUO

Smart switches are among the best products to increase your home's IQ, but they depend on a wireless internet connection to function correctly. When this connection is interrupted, the switch can stop responding to voice or app commands. You may also notice the LED on the switch turns red or blinks. Hi, again I think I messed all I replaced the smart switch today it worked perfectly until light switch sparked when one of the cable tightening screws touched metal housing and circuit breaker tripped. Before getting starting wiring a smart switch, be sure to familiarize yourself with the introduction to wiring and basic (non-smart) switch wiring. It would also be beneficial if you have already wired a single smart switch and a three-way smart switch. If you have not, review wiring a smart switch and wiring a three-way smart switch for good overviews. Four Way Smart Switch Wiring Requires a neutral wire at the switch. If you are unsure about the installation of this product please consult a qualified electrician Finally, Feit smart switches take a little more work to reset. First, you’ll need to remove the wall plate. Once you remove the plate, you’ll find an air gap slider inside. Pull out the air gap slider, then hold the button on the switch for 20 seconds.I can only see one connector with a brown and blue wire going into it. Any wire with a piece of tape around the end means its a switched live wire. Again, ensure the power is off at the breaker. Disconnect the old light switch completely by disconnecting each wire one by one. Take note of which wire is which as you disconnect them to avoid confusion later. If they’re unlabeled, grab some different colors of electrical tape and label them as you go. Hi everyone, Basically, I am planning to replace the light switches in my new build house with smart switches and as the switch has WiFi built-in it needs constant power to work so will require a neutral wire Before setting up your smart light switch, read the entire instruction manual to make sure you understand its wiring and function. Designs vary, so don’t worry if they look very different from a traditional switch. Set timers and routines for specific lighting needs whether this is for cosy evenings, morning wake ups or to have party anytime.

TCP Smart switch 2 gang, 1 is 2 way. - Screwfix Community Forum TCP Smart switch 2 gang, 1 is 2 way. - Screwfix Community Forum

Our responsibility within the lighting market extends beyond just supplying light bulbs; TCP exists to make lighting an experience that will transform a house into a home….. and what better way to do that than with smart controlled lighting solutions. A smart switch is a key element of a smart home. Before getting starting with wiring, be sure to familiarize yourself with the introduction to wiring and basic (non-smart) switch wiring.We all have three-way switches somewhere in our homes. These are switches where one light can be controlled by two switches. Replacing an existing three-way switch with a smart switch may seem complicated. But the process is actually pretty simple and logical and makes use of existing wires in most junction boxes. The Wires In a Regular Three-Way Switch

TCP Smart Wifi Wall Switch Double White Uk | Homebase

Tool-Free Battery Replacement - Easily replace batteries after installation, no need of other tools. Add-on switches – For each add-on switch, follow the exact same steps outlined above for the three-way switch. For the add-on switch in the middle of the chain, just connect both red wires to the traveler terminal. Totally agree with this. I had an 'old technology' smart system based on the X-10 protocol where all the switching was done by switch/ dimmer modules. I changed it to Philips Hue having got my head around the intelligence being in the bulb. It means you can keep standard wiring and switches. If the system fails you can still use switches to use the lights etc. And can take it all with you if you move. And it gets around the no neutral at the switch issue. When working correctly, smart light switches offer convenience and voice control of your home’s lighting. Unfortunately, the devices depend on a wireless network. That means most switches are prone to occasional disconnection. However, this disconnection only occurs for one of a few reasons, and most aren't serious. Connect the red wire (traveler) to the upper left terminal of the add-on switch. This provides a connection between the primary and add-on switches.If the switch works, you can move on to the next step. If your switch does not turn on, you need to reexamine your connections. This may seem strange at first, but it should make sense. In a smart home, only one switch needs to be controllable by the smart network. The other add-on switch is just there for us humans to be able to manually toggle the switch. How to Wire a Smart Three-Way Switch Connection cycle will Appear. Text located on the bottom of the screen will begin to be highlighted green. Once all 3 points are highlighted in green, the cycle will complete. Don’t automatically think that setup in all your rooms will be the same. Wiring can vary from room to room. First, let’s start with a regular (non-smart) three-way switch. The main difference between a basic single switch and a three-way switch is that the three-way switch has an extra red wire (traveler). This extra wire provides another connection between the switches so that either switch is capable of sending power to the light. How a Smart Three-Way Switch Works