Joined in 2023 
82 
63 About this deal
As the name suggests, Soft Close Hinges allow cabinet doors to gently and quietly close using a hydraulic mechanism. This type of hinge is ideal in a heavily used space such as a kitchen. It can even extend the life of the cabinet doors as it reduces the impact created with each close. Better yet, this type of cabinet hinge is great for homes with multigenerational users, reducing the risk of injury to children or those with slower reflexes, as the doors shut softly.
These hinges allow for 270 degrees of motion, from closed 0° to 270° full open parallel with the side panels. This was developed out of an effort of running into tolerance issues with the spec hinges not allowing much room if the two panel doors are used and are slightly cut larger by only 1 mm or so. I ran into issues closing and the doors hitting and needed something that allowed more horizontal movement. Note: Un-tested but the holes should line up with Randell's hardware for the hinges if you are looking to swap for more swivel.Butt Hinges are classic, easy to install, and are used in a wide variety of applications. They are the most common option, and the most cost effective. Simply put, this cabinet hinge is created with two rectangle leaves which are joined together with a pin. Attach the face_plate_bottom to the face_plate_top using 2x M3 x 8 mm Bolts and 2x Hex Nuts - Keep the bolts loose for now If you're going for a super sealed enclosure, then these hinges are not for you. In testing ( at the moment with only 2 hinges per panel ) I found after opening and closing the doors several times, they would slowly lose alignment ( only by fractions of a mm ) and just need a little push to re-align so the panels would close properly and not collide. This means you'll probably have a gap of a couple mm between the panels at the front if you don't want to be driven crazy by them not staying super aligned. A potential fix would be to print 3 hinges for each panel but I am yet to test this although I strongly recommend you do use 3 hinges per panel if you have a printer larger than 250x250 ( what I'm testing them on ). Update Log Once all the hinges are on the frame. Slot in a panel on one side, before tightening down the M3x8mm Bolts in the faceplate assembly. And repeat for the other panel.
Blind Corner - 95° hinge used where doors open inline with the panel it attaches to, used in corner cupboards.
Installation
When fitting a caravan, you will want to explore our range of Caravan Hinges. These come in a variety of opening angles, allowing the users to access their storage which may be in a less traditional area, for example, placed in the corner of where the wall and ceiling meet. We have the right hinges to allow you to install there.
There is a left (a) and right (b), you will need to print 2 for each side. There are 2 versions of each of the hinge faces if you don't want a Voron logo or want to mix and match. Multiple depths are also provided. Should you need a specific depth and no access to Fusion, feel free to reach out to me on discord chrisrgonzales#0731 The 4 mm is typical 3 mm panel and 1 mm foam , and 6 mm files are for 3 mm panel and 3 mm foam. The design of this hinge is based on chrisgonzales already incredible 270 degree hinges. The main goal of this remix was to have the front panels mounted in a way that didn't use any VHB tape or holes that needed to be drilled into the acrylic, and of course, use minimal amounts of additional hardware. After many design iterations and improvements I came to a solution. Important NoticeEasy-On - A simple hinge solution that doesn't require a cup hole drilling - used on thin doors and sheet metal.
TIP: When installing with tape, mount the panels with the same corner clips that are used on the sides and top - you can temporarily take a couple from each panel. Use the corner clips to position the doors where they should be when closed. Install the hinges on the sides at the desired positions and apply the double-sided adhesive tape to the hinges. Then swing the hinges inwards touching the doors and secure them. Once you feel the adhesive is secure, remove the corner clips. Butt hinges are the most commonly used hinge. They come in different types, but they can typically be defined as hinges made up of two matching leaves connected by a joint of some kind. This joint traditionally holds a pin.Made subtle changes to dimensions to hold panels closer together whilst having them fully seated in the clamps for maximum strength, also changed recommended print settings for stronger face_plate_bottom.stl. Using Foam Tape Clip-On: Easy fixing clip in function on the hinge arm and mounting plate allowing doors to be installed/removed without unscrewing.
Great Deal 
New Comment