Hammerite Kurust Rust Remover for Metal. Rust Treatment and Rust Converter for Metal Interior and Exterior to Remove Brown Spots - 90ml

Product Information

Both Dinitrol with its rc800 and Hammerite Products with their Kurust sell rust convertors. I'm now going to tell you why we don't use them and neither should you. But it offered very little in the way of long-term protection to our sample. The unpainted area was uniformly rusty again and it was starting to develop on the other side too. Loctite SF7503 Rust Remedy Remote areas/Scottish Highlands and non-UK Mainland areas may be subject to additional charges and a longer delivery time. This is determined by our couriers not Rustbuster. It wasn’t worth the time and effort either. Unlike the other fluids, the Rustins didn’t seem to bond to the metal at all, meaning it just sat on top of the surface. This meant it struggled to protect against our salty spray and actually started flaking off by the end of our test, revealing the bare metal underneath. Jenolite Rust Convertor Liquid

Waxoyl or Before 'n' After's improved Waxoyl or the Before 'n' After CR coatings are infinitely better at killing rust than rust converters. The rust converter plus waxoyl may appear at first sight like "belt and braces" but the fact is that the rust converter will just ruin the whole job. Special precautions should be taken to avoid inhalation of dust during surface preparation of pre-1960’s paint surfaces as they may contain harmful lead. Caution Oil and grease contamination will prevent the conversion First of all, a lot of the the underneath of most cars, especially Land Rovers, is contaminated with oil and grease from leaking oil seals etc. On oil or grease contaminated areas, unless the underside is extremely thoroughly cleaned, degreased, and then completely dried, the rust converter will not work. So you are very likely to have the nightmare scenario of an ineffective, poorly adhering coating sitting between the rusty surface and any coating of rustproofing wax, making the rustproofing wax totally ineffectual. Waxoyl, and my similar, more formulted CR coating, are petrochemicals very similar to oil and grease from leaking seals of mechanical parts on the underbody. To help you achieve this, we offer a full suite of rust treatment products, including: Car rust remover After you have blasted them mix just a small amount of the epoxy and apply it with a paint brush. It can then be left untill you are ready to prep and paint.

Ask an expert

It did a good job of protecting our sample too. Just a few dots of the dreaded red were visible on the unpainted side. But it didn’t score higher as it’s expensive if you buy it in this small bottle and doesn’t offer significant advantages. Neutrarust is available in larger bottles though, so it could start to make financial sense if you buy in bulk for bigger jobs. Rustins Don't use sand because of the health risks and do wear the proper PPE which must include a decent mask. Use waxoil, this is great stuff however does dry out after so long not sure how long but it does, so has to be re-applied (if it was me id do it before every winter) So I would touch up the rust spots with 87 / 90a rub level with the surrounding paint then prime the whole area with standard epoxy primer.

You know you have a serious product when it has stamps of approval from organisations like NATO and the Ministry of Defence. If it works on tanks and warships then the bottom of your Cortina probably won’t be an issue. A handy tub of Hammerite’s popular Kurust rust converter. Transforms rust to a sound surface in 15 minutes, ready for painting in just three hours.So that’s what Kurust looks like, almost a milky substance, I don’t know what I was expecting to be honest but here it is. The Metal Shows Kurust converter, the clear winner out of the 4 converters tested. Score marks through the apparently converted rusty surface tmade with a Stanley Knife blade. So if you are going to try and use some rust convertor, I believe you should remove all the excess rust first (like other people have already said) then go over it with the kurust or another product that may even be better, and make sure when you apply it you really work it in so it goes into any pitted areas. What i did was go in a circular motion with the brush to work it in then straight lines to finish it off. The first thing you need to do is pour some Kurust into a separate tub. You don’t want to put your brush in and out of the tub as any rust particles on your brush could end up ruining the entire tub.

As you can see this is a really rusty piece of metal, so should be a really good test subject. The Metal Wire Brushed Using KurustUnwanted Food or Drink Products - Once supply conditions are broken, there are a number of factors outside of our control that can affect the quality of a product. Therefore perishable goods such as food and drink cannot be returned.