Silverline Soldering Sponges 10pk (633932)

Product Information

More advanced models and various add-on accessories may provide a number of reassuring built-in safety features. However, even versions bought as part of a comprehensive soldering iron kit can carry plenty of potential to cause serious and lasting injury if used carelessly.

Apply a small amount of the cleaning paste directly onto the soldering iron tip and then press it against a damp sponge or cloth to remove all residue from the surface of the tip. The resin is non-corrosive, but it does not have the cleaning properties of zinc chloride. A blow torch or soldering iron is made, a device for heating base metals and melting solder and flux. In this two part Kitronik University resource we’re going to show you how to clean and maintain your soldering iron. Read on for a written guide or skip to the video. The CLMB will automatically clean the tip in just one second. A photoelectric sensor detects the tip when you introduce it into the opening and then activates the brushes. With the CLMS model, the brushes will run in either a continuous mode or when you press the button on the lower side of the opening.

This section will explain the tools of the trade. Some of these you will need, some of these you will not. The first (and most common) apparatus is the simple yellow sponge. The downside of brass sponge is that it doesn't clean the tip 100%. There's almost always some solder remaining after using it. Which is normally a good thing, except when working with small/fine-pitch components (<0603 or <0.5mm pitch). If you have solder residue on the tip when doing such joints, it will mess everything up, so brass sponge isn't even an option for fine pitch work. More advanced tip-cleaning kits can also leave you with a fine solder layer across the tip as part of the cleaning process, which helps to prevent tool oxidation over time and improves the longevity of replaceable tips These types of soldering metal use a very higher melting point than the metals used in hard and soft soldering. However, it is similar to hard soldering, the metal being bonded is heated as opposed to melting. Make sure to rub in a circular motion until all residue has been removed from the surface, then rinse with warm water and dry completely before using again.

Do not use any soldering iron or other item of electrical equipment that shows visible damage to the tool body, cabling or plug Its function is to prevent oxidation of the surfaces to be soldered or to dissolve oxides that settled on the metal surfaces during the healing process. Although corrosive, Zinc chloride is the most common soldering flux. With the implementation of lead-free soldering, besides the wet sponge there are alternative ways to cleaning the tip. Their use depends on how much residue needs to be removed, maintenance and the technology of the soldering method. Step 1: Mount The Component– Begin by inserting the leads of the LED into the holes of the circuit board. Flip the board over and bend the leads outward at a 45′ angle. This will help the component make a better connection with the copper pad and prevent it from falling out while soldering. In my experience, both accessories are complementary because I find soldering sponges faster for daily work.To begin cleaning, use a wet sponge and rub off any remaining solder or residue that has built up on the tip of the iron. This should remove most of the dirt and oxidation from its surface.

Unlike cellulose sponge, brass wool does not require dampening, which means it doesn’t lower the temperature of your soldering iron tip when cleaning. This feature can be advantageous for tasks that require maintaining a consistent iron temperature. To clean the soldering iron without flux, start by unplugging it and letting it cool down completely before attempting any maintenance. An explanation of why we need to clean the tips and a step by step guide. Includes a video guide to tinning. The brass wool is an alternative to the sponge, needs less maintenance but does not decrease tip temperature, which is why it is better suited to sometools with low thermal response. A disadvantage to the brass wool is that it retains residue which in turn may fall on the PCBs if there is no splashguard. The brass wool holder should be heavy enough to avoid having to steady it when being used.If after cleaning on the sponge / brass shavings the tip is still not shiny then melt a small amount of solder onto it and clean again. The flux in the solder will help to clean the tip.

Always return the iron to its cradle or stand when not in use - never lay it directly on a work surface, table or bench Step 2: Turn on your soldering iron and let it heat up. If you have a soldering station with an adjustable temp control, set it to 400′ C/ 752′ F. The solder, which is mostly composed of lead and tin, has a melting range of 150 to 350°C. A suitable flux is always used in soft soldering. Some brass cleaners have a thin coat of flux applied to the brass wire that helps to clean and tin the tip. Keep the iron in place and touch the solder to the wire until it’s fully coated. Repeat this process on the other wire.

Tinning your soldering iron tips is a great way to extend their lifespan. Tinning means applying a thin layer of solder to your soldering iron tips. This protective layer prevents your soldering iron tip from oxidising. It also makes soldering easier, as the layer creates a heat connection between your tip and the part you are soldering, which increases the efficiency of the heat transfer. Yes, you can use rubbing alcohol to clean a soldering iron. It’s important to remember to unplug the iron and let it cool before cleaning. You should also avoid using any abrasive materials when cleaning with alcohol. Wipe the iron down with a cloth soaked in rubbing alcohol and then dry it off with a clean cloth. Do you need to clean helping hands after soldering?