Oatey 30372 No. 95 Tinning Flux, Lead Free 8-Ounce

Product Information

When the wires have high-temperature demands: Soldering an electrical wire with a tin coating improves the heat range that the wire can withstand and operate under. If you have wiring that needs heat-resisting properties, tinning is an excellent option.

Tinning the tip of your soldering iron makes it last longer and easier for soldering wires. The basic tinning of the soldering iron tip is necessary before any efficient soldering work gets completed. Read more below for steps of the process of tinning the soldering iron tip.Safety should always be a top priority when working with soldering irons. Before you start, make sure you have taken the necessary precautions to protect yourself and your surroundings. Soldering flux is only corrosive once it is heated up and in its liquid form. As long as it is still a paste when you start working with it, you don't need to worry about getting any on your skin. Apply a small amount of flux: Take a small amount of flux on a flux brush or applicator. Gently brush the flux onto the soldering iron tip, ensuring complete coverage. Be careful not to apply too much flux, as it can cause excessive smoke or splattering. Apply the flux with a brush: Do not apply it with your fingers and be sure to wash your hands thoroughly after use. Tinning makes the wires that are coated better in many ways. The operating temperature range gets increased when wires get coated with tin. Also, tinning increases the wires’ corrosion and water resistance. Finally, tinning coats on wires increases the mechanical strength of copper wire.

Melt or “sweat” the solder material on and around the pipe joint while keeping the heat constant throughout your work. Prepare the soldering iron tip: Before applying flux, make sure the soldering iron tip is clean and free from any debris or old solder. Use a damp sponge or brass wire cleaner to remove any residue. Insufficient heat: If your soldering iron is not reaching the proper temperature, you may face difficulties in tinning. The solder may not melt properly, leading to incomplete tinning and weak solder joints. While you work on wires with a soldering iron, tinning is an excellent idea: as the tin melts and spreads out over and into the wiring coating, the wire surface’s consistency increases. Tinning a wire helps conductivity and efficiency of wires only as much as the specific wire material is susceptible to soldering.By following these steps regularly, you can keep your tinned soldering iron in excellent condition and ensure optimal performance for all your soldering projects. Plug-in and wait: This is the simplest method. Plug in your soldering iron and wait for it to reach the desired temperature. Most soldering irons have an indicator light that turns off or changes color when the iron is heated and ready for use. Uneven coverage: Uneven coverage of solder on the soldering iron tip can occur when the solder is not distributed evenly or when there are areas that are missed during the tinning process. This can result in poor heat transfer and unreliable solder joints.

For large-diameter piping, move the heat around the joint to ensure adequate solder flow around the circumference of the joint. Please provide us with the Superior part number(s) AND the lot number(s) for the product(s) you need a C of QA for. Lastly, tinning helps to extend the lifespan of your soldering iron. By regularly tinning the tip, you reduce the wear and tear caused by oxidation and corrosion. This means that your soldering iron will last longer and provide consistent performance over time. In 1891, the United States made 11,000 tons of tinplate and imported 325,100 tons, but in 1899, it made 360,900 tons, importing only 63,500 tons (mostly for re-export). British exports were further hindered by the Dingley tariff, which removed the advantage of Welsh plate on America's Pacific coast, [11] had by 1900 increased to more than 849,000,000lb, of which over 141,000,000lb were terne-plates. The total imports in that year were only 135,264,881lb. In later years, again, there was a decline in the American production, and in 1907 only 20% of the American tinplate mills were at work, while the British production reached 14 million boxes. [2] Add rosin core solder or flux, which is ideal for the soldering iron tip because it aids the solder in binding to the iron tip.Soldering iron: The main tool used for tinning. It is essential to have a good quality soldering iron with a clean and undamaged tip for effective tinning. Soldering low lead brass can be daunting, since it doesn't conduct heat well. Using tinning flux will help eliminate the human error of soldering low-lead brass and help fill the joint to create a leak-free connection.

Since low-lead brass doesn't conduct heat as well, start by heating the pipe a little bit right outside of the hub or directly at the joint until the flux starts to bubble or activate. Then apply heat to the base of the fitting. There is also a difference between tinning flux and tinning a soldering gun. With tinning flux, you will concentrate on adding the flux directly to the inside of the pipe to help create the joint you want. You will need to completely clean out the pipe and have it ready to go to make the joint work completely. King, P. W. (1988), "Wolverley Lower Mill and the beginnings of the tinplate industry", Historical Metallurgy, vol.22, no.2, pp.104–113

Always keep your soldering iron in a stand while it is on. The tip will get very hot, so it shouldn't be allowed to rest on any surfaces as this may start a fire. Don't leave your soldering iron unattended while you are using it. If you are working on piping, it is important to consider which type of flux is best for your needs. The standard flux works well for a lot of projects you want to handle. It is strong, will protect the pipes, and can make sure you do not end up with water leaking out of the pipes. You can also work with a soldering gun. This is a small gun, one that looks similar to a pistol, that is electrically powered and used to solder together metals. This is done because you will use a tin-based solder to get a strong bond through the electricity that goes through it. You can use the trigger to help turn on the electrical current with one hand. P. Jenkins, ' Twenty by Fourteen': a history of the south Wales tinplate industry 1700-1961 (Gomer, Llandysul, Dyfed 1995). Solder melting: Touch the tip of the soldering iron to a small piece of solder. If the solder melts and forms a liquid bead on the tip, it is a clear indication that the iron is hot enough for tinning.