276°
Posted 20 hours ago

Trend Multi-Functional Table Routing Jig, MFT Style Worktops, Plunge Router Compatible, Durable Material, Corner Radii & 45 Degree End Cut, MFT/JIG

£98.945£197.89Clearance
ZTS2023's avatar
Shared by
ZTS2023
Joined in 2023
82
63

About this deal

sets of plastic sawhorses. One of them is a Stanley set which has notches in the top to fix 2 pieces of CLS. I speak from experience as I have done both… made an MFT style without and with the Parf system... initially, I took care and took my time to ensure absolute accuracy with my without build… the fact that afterwards I even considered the Parf system, speaks for itself.

I haven't read all the comments so I hope I'm not repeating any good advice and unintentionally exposing myself to a pissing contest. move the jig along, securing it in place with the supplied aluminium dogs and additional clamps if required I was considering a review and decided to do a search first and made a few hits… not being an avid reader and wade through all the responses, I hope that this response covers the subject matter with stuff that may not have been covered. Developed by UJK and Peter Parfitt, the UJK Parf Guide System gives you a simple way of producing a pattern of accurate 20mm holes. This allows you to make as many workstations as you desire. Most importantly accuracy is assured and this jig will not allow for cumulative errors due to the way it works. Note that your target piece needs to be flat as you work on the hole pattern. 1/4" out of flat and you ll be fighting the geometry. So, if you are concerned about getting a flat base, I d work on that first - using a torsion box method.On a philosophical side - isn't it a bit crazy how much we are geared for perfection, but not wanting to practice? I won't begrudge saving money but I do begrudge people claiming similar accuracy… If you have actually achieved similar accuracy, I could just about guarantee that if you costed time, it would have cost twice the price of the Parf... But is it possible to DIY your own ? Well, even if your workshop is pretty well equiped, it's not that easy, but definitely yes, you can. Any individual could make a table and fix rails, so I will not cover these subjects. I will focus on two fields that can bring success to your work : Credit subject to status and affordability. Terms and conditions apply. Axminster Tool Centre Ltd trading as Axminster Tools is a credit broker and is Authorised and Regulated by the Financial Conduct Authority. Credit is provided by Novuna Personal Finance, a trading style of Mitsubishi HC Capital UK PLC, authorised and regulated by the Financial Conduct Authority. Financial Services Register no. 704348.

A pair of UJK Technology Parf Dog Rail Clips from Axminster which keep the rail butted up against the dogs. For less than the price of one replacement top for a Festool MFT, you can get the jig, make your own replacement top and then start adding gridwork tops for the other work surfaces in your shop. With an array of clamps and end-stops there’s no limit to the workholding arrangements you can set up on a gridwork table. Another option (if you haven t realized it by now) - get a CNC shop to make a one plate of at least 11 20 mm holes in a straight line (aluminum or laminated mdf best) - then duplicate that for a nice set of straight-line hole plates. You can set up parallels and spacings that follow previously set holes (and your own guides) to make accurate hole patterns. Another option is the Part fence ( https://www.axminstertools.com/us/ujk-parf-system-fence-stop-kit-1-000mm-107462?glCountry=US&glCurrency=USD ). Leaves some money to buy a dog hole set and pattern bits. You can come up with quite accurate placement methods with uniform offsets that fall within the tolerance of the hole patters of the original plates. Furthermore the OP's comment of " that will sit on the shelf 99% of its life", no malice intended, however, shows little foresight. I laid it out pretty carefully, and drilled it on a drill press. It extends 24". After using it a few times I pretty much ignore the first row of holes now, That puts the first line into a nice spot, but if you play around with a paper template on layout you'll find what feels right for you.I keep looking at “better” alternatives but I can achieve speed, accuracy and flexibility here at minimal cost. This way I can support a 2800mm x 600mm board, trim both ends, make accurate, clean square cuts every time. When I need to make 7 480mm shelves, I just clamp a stop against the 480mm mark on the fence and lo and behold, I’ve got a production line going. The Hole boring jig needs a plunge router and a spiral upcut bit. It can be used to make small accessory pieces that could fit onto the MFT system, whereas the parf guide system seems more suited for a large full size MFT tables. Note that your target piece needs to be flat as you work on the hole pattern. 1/4" out of flat and you'll be fighting the geometry. So, if you are concerned about getting a flat base, I'd work on that first - using a torsion box method. Whether you like it or not, the Festool brand makes handy tools that works pretty well. Most criticism cames from the price tag. Some people says it worth the price and some desagree. An intersting element of the Festool system is the MFT table (MFT for multifunction table), actualy in version 3. It is both a workbench and an precision tool. You can accurately do a lot on it : assembly, cutting, drilling, make grooves, rabbets, and all you usualy do on a standard workbench. But at >600€ for the dry table, >100€ for the sacrificial table top spare part, and > 100€ for a pair of clamps, a lot of people can't afford it for such a hobby thing. So do I.

Another option (if you haven't realized it by now) - get a CNC shop to make a one plate of at least 11 20 mm holes in a straight line (aluminum or laminated mdf best) - then duplicate that for a nice set of straight-line hole plates. You can set up parallels and spacings that follow previously set holes (and your own guides) to make accurate hole patterns. Another option is the Part fence ( https://www.axminstertools.com/us/ujk-parf-system-fence-stop-kit-1-000mm-107462?glCountry=US&glCurrency=USD ). Leaves some money to buy a dog hole set and pattern bits. You can come up with quite accurate placement methods with uniform offsets that fall within the tolerance of the hole patters of the original plates.

Register

Asda Great Deal

Free UK shipping. 15 day free returns.
Community Updates
*So you can easily identify outgoing links on our site, we've marked them with an "*" symbol. Links on our site are monetised, but this never affects which deals get posted. Find more info in our FAQs and About Us page.
New Comment