Joined in 2023 
82 
63 About this deal
Hot-swappable input/output device that plugs into an Ethernet SFP+ port of a Cisco switch (no need to power down if installing or replacing) Higher power consumption compared to optical connections (especially when multiple units are used in the switch). The GLC-BX-D-I and GLC-BX-U-I are the Industrial temperature rated (IND) counterparts of GLC-BX-D and GLC-BX-U SFPS. This allows link operation in harsh environmental conditions where the module case temperature can be in the range -40°C to 85°C. The Cisco SFP-10G-SR-I is a multirate 10GBASE-SR, 10GBASE-SW and OTU2/2e module for industrial operating temperature range. This module also supports CPRI datarate options 3, 4, 5, 6, 7, 7a, 8. It supports a link length of 26m on standard Fiber Distributed Data Interface (FDDI)-grade Multimode Fiber (MMF). Using 2000MHz *km MMF(OM3), up to 300m link lengths are possible. Using 4700MHz *km MMF (OM4), up to 400m link lengths are possible. The SFP-10G-BX40D-I and SFP-10G-BX40U-I SFPs support Digital Optical Monitoring (DOM) functions according to the industry-standard SFF-8472 Multisource Agreement (MSA). This feature gives the end user the ability to monitor real-time parameters of the SFP, such as optical output power, optical input power, temperature, laser bias current, and transceiver supply voltage.
The SFP-10G-ZR-I has a cold start at -40 ⁰ C, the transceiver will be operational except optical traffic is not supported from -40 ⁰ C to -28 ⁰ C, all other low speed features (DOM, I2C, etc.) are operational. The module is fully operational -28 ⁰ C to 85 ⁰ C. The Cisco 10GBASE-LRM Module also supports link lengths of 300m on standard Single-Mode Fiber (SMF,G.652). The Cisco GLC-BX40-D-I, GLC-BX40-DA-I, and GLC-BX40-U-I SFPs operate on a single strand of standard SMF. However, they do exist as "Direct Attach Cables". In this form, the modules are attached to either end of the cable, and are not designed to be removed. As @JourneymanGeek points out, Ethernet specifies what signals to transmit and receive, and puts requirements on the characteristics of the cable - certain signal loss is acceptable at certain frequencies, and certain inter-pair cross-talk levels (where the signals on one pair can be " heard" on another pair).The communication over a single strand of fiber is achieved by separating the transmission wavelength of the two devices. The GLC-BX80-D-I and GLC-BX80-U-I SFPs also support Digital Optical Monitoring (DOM) functions according to the industry-standard SFF-8472 Multisource Agreement (MSA). This feature gives the end user the ability to monitor real-time parameters of the SFP, such as optical output power, optical input power, temperature, laser bias current, and transceiver supply voltage. When shorter distances of Single-Mode Fiber (SMF) are used, it might be necessary to insert an inline optical attenuator in the link to avoid overloading the receiver. A 10-dB inline optical attenuator should be inserted between the fiber-optic cable plant and the receiving port on the SFP at each end of the link whenever the fiber-optic cable span loss is less than 8 dB. DOCSIS outlines requirements for the signals and cable, but I don't believe it dictates the termination / connectors. In the UK these are typically terminated with F-Type Coax connectors. The communication over a single strand of fiber is achieved by separating the transmission wavelength of the two devices. SFP-10G-BX40D-I transmits a 1330-nm channel and receives a 1270-nm signal. The SFP-10G-BX40U-I transmits at a 1270-nm wavelength and receives a 1330-nm signal.
Optical interoperability with 10GBASE XENPAK, 10GBASE X2, and 10GBASE XFP interfaces on the same link Twisted-pair cables consist of two conductors of a single circuit twisted together, which reduce the effects of EMI and mutual interference between pairs and improve electromagnetic compatibility. Nowadays the cables are shielded with aluminum foil to increase protection against crosstalk on neighboring lines. There are Cat5e, Cat6, Cat6a, Cat7, Cat8 Ethernet cables that can be used in your network solution. And this 10Gb copper SFP+ solution can be paired with Cat6a/Cat7 or Better for a transmission distance of 80m. Latency An SFP - Small Form-factor Pluggable Transceiver - is just a little device that converts a standard set of signals to another standard set of signals. They often convert to fibre Ethernet connections, but can equally provide copper Ethernet or even direct SFP-SFP connections.A SFP-10G-BX40D-I device is always connected to a SFP-10G-BX40U-I device with a single strand of standard SMF with an operating transmission range up to 40 km. The Cisco SFP-10G-ZR is a multirate 10GBASE-ZR, 10GBASE-ZW, and OTU2/OTU2e module. It supports link lengths of up to about 80 kilometers on standard Single-Mode Fiber (SMF, G.652). This interface is not specified as part of the 10 Gigabit Ethernet standard and is instead built according to Cisco specifications. Cisco quality Identification (ID) feature enables a Cisco platform to identify whether the module is certified and tested by Cisco
Information about Cisco’s environmental sustainability policies and initiatives for our products, solutions, operations, and extended operations or supply chain is provided in the “Environment Sustainability” section of Cisco’s Corporate Social Responsibility (CSR) Report. The Cisco 10GBASE-ER Module supports a link length of up to 40 kilometers on standard Single-Mode Fiber (SMF, G.652). The Cisco 10GBASE-SR Module supports a link length of 26m on standard Fiber Distributed Data Interface (FDDI)-grade Multimode Fiber (MMF). Using 2000MHz *km MMF (OM3), up to 300m link lengths are possible. Using 4700MHz *km MMF (OM4), up to 400m link lengths are possible.
The battle between fiber optic SFP module and RJ45 SFP module still hot in the field of the transceiver module. Optical SFP module with LC or SC optical connectors is used in Fast Ethernet and Gigabit Ethernet allowing transmission distance up to 120km. Compared to optical SFP, RJ45 SFP module has the following advantages:
Related:
Great Deal 
New Comment