Walfront RS232 to RS485 Serial Converter Passive Converter Adapter Communication Data Interface Networking Supplies

Product Information

In some cases, if the communication distance is long (above 1000 feet) and if the baud rate is over 115kbit it is recommended to put a resistor (typically 100 ohm) at the RS485 node (across the A and B lines). Adding the termination resistor does however RS485, also known as TIA/EIA-485 is a standard serial communications protocol defining the electrical characteristics of a serial converter, drivers and receivers for use in balanced RS485 digital multipoint systems. Even RS485 is not commonly as popular as RS232 it is extremely useful for converters in industrial and commercial environments. A RS232 - RS485 converter is often used in industrial data acquisition and control applications where multiple serial devices communicate with each other through a converter. When shopping for a RS232 to RS485 converter you should first determine if you need an industrial strength or a commercial/consumer grade converter, this depends on which environment you plan to use the converter. Next you should determine if you need and isolated or non-isolated converter, where after you can decide if you need an externally powered converter or if you can use a port-powered converter. Next you can find the connector type you need, either DB9 or DB25 connectors, terminal screw header, RJ11 connector or a combination hereof. Finally you should decide if you want LED lights for the TX/RX lines, this can be very helpful when troubleshooting. RS232 to RS485 converters can be either isolated or non-isolated. An isolated RS232 to RS485 converter have optical isolators separating the data lines inside the unit, this prevents noise, high voltage spikes, surges and ground-loops from damaging your computer or the equipment you have connected to the converter. Some RS232 to RS485 converters even have the externally power supply isolated from the rest of the converter to provide additional protection. Usually isolated converters are only used if the user wants to additionally protect the equipment connected to the network (in case the equipment is of high value), or if there are reasons to suspect high voltage spikes or similar in the network. What is called 'Automatic Send Data Control', which controls the data flow, is strongly recommended for most applications and devices, this feature is built into most modern RS232 to RS485 converters.

RS232 to RS485 converters are mostly used in industrial and commercial environments. The reason is that the RS485 converter can be used for multi-drop networks, meaning that you for example can connect multiple RS485 devices to one computer. Up to 32 devices can be connected in one network to communicate on a single pair of wires (plus a ground wire), and the number can even be increased by using RS485 repeaters. This type of communication is called half-duplex communication. Most quality RS485 converters can communicate in this manner of up to 4000 feet (1200 meters). The RS485 converter

How to choose the right RS232 to RS485 converter.

Many port-powered RS232 to RS485 converters provides an option for supplying external power. If in doubt, use an externally powered converter, then you are sure that it gets sufficient power. I using for example a USB to Serial adapter these same assumptions can be applied. The serial RS232 to RS485 converter and RS232 to RS422 converter units, also called serial converters, are small electronic devices used to convert a serial RS232 signal, (for example the COM port in older computers) into either RS485 or RS422 signals. The typical serial converter does this in both directions which is also referred to as a bi-directional converter. dramatically increase power consumption so it should not be done, and is mostly not needed at shorter distances. Due to the increased power consumption termination is also rarely done when using port-powered converters. The RS485 converter interface uses two wires for communication, one for transmitting and one for receiving data, which is referred to as a half-duplex communication converter. The typical common-mode voltage range for a RS485 converter is -7V to +12V. The RS422 converter is used for data transmission, using balanced or differential signaling, it is mainly used in industrial and commercial environments since lots of process equipment and machinery have this protocol built-in. The RS232 - RS422 converter is also often used in older serial devices such as older PLC's and terminal equipment.

In contrast to EIA-485 (which is multi-point instead of multi-drop), EIA-422/V.11 does not allow multiple drivers but only multiple receivers. The RS485 Master could be a computer and the slave could for example be a camera. As you can see the data lines A- and B+ are simply connected to the RS485 Slave's A- and B+ respectively. The converters will communicate with only A- and B+ connected, however it is very important to also connect the ground wire in the finished system to establish a steady reference point to prevent data loss and other bad things. Quality Guarantee - SerialComm converters are low priced, high quality products and made to last a lifetime. They are manufactured in a ISO-9001 certified facility using surface mount technology with lead free components. All converters are pretested prior to shipment and are fully guaranteed for 5 years. There are no converters, Commercial or Industrial that surpass SerialComm's quality standards at any price tag.some are isolated some are not, some has more than one RS485 port, some has LED lights for indicating RX/TX data flow, some are port-powered and some needs an external power supply, some are industrial strength, some are consumer products. We will here not go into the specifics of how the RS232 or RS485 protocol works, but if you are interested in this then there is lots of RS232 and RS485 information on Wikipedia, including how a USB to serial adapter works. We will however demonstrate the most common ways of connecting a RS232 to RS485 converter.