Artillery Sidewinder X1 3D Printer, V4 Version Lattice Glass Heat Bed Aluminum Extrusion Frame & Filament Runout Sensor & Power Failure Recovery 3D Printering, 300x300x400cm

Product Information

As you can see, my TFT connector was full of glue so I had to remove the cable including the connector. Most budget 3D printers these days use an aluminum V-slot extrusion / roller wheel motion constraint on each axis. The prints which have decent layer lines dont stick to the bed in some places and the ones who stick have layer separation.

Artillery Sidewinder X1 3D Printer, V4 Version Lattice Glass Artillery Sidewinder X1 3D Printer, V4 Version Lattice Glass

The geometry of the ground surfaces ensures that the carriage can only move along a single axis, and cannot wiggle or twist. This is a guest post made by whoppingpochard , an awesome member of the 3DPrintBeginner Discord Server. Due to popular request, the Sidewinder X1 Firmware containing the BLTouch settings is currently available.You can now power up the printer and heat your hotend to 270C then do the final tightening of the nozzle. I liked that the axes/printhead were fixed with cable ties and the cables with proper adhesive tape. A Titan Aero clone with a pancake motor powering it, and a Volcano style hotend melts plastic for the Artillery X1. The holes for the MGN12C blocks should be on the left side of the carriage, closest to the belt attachments. On top of it, the heatbed (or Y axis) runs on a 60x20mm aluminum extrusion which is great for stability.

Artillery Sidewinder X1 Review (2023) -Features, Performance Artillery Sidewinder X1 Review (2023) -Features, Performance

If you’d like to talk more about Klipper, find me on the 3DPrintBeginner Discord Klipper thread and the Artillery Discord. Read the full guide carefully and install Klipper on Sidewinder X1 only after you properly understood all the steps involved.The BMG Wind will be my go-to direct drive extruder upgrade for any printer in the future because of the reduced weight, compact design and improved performance compared to other setups. Aside from some hex wrenches and a pair of pliers, the only tools you need to complete this project are some sort of drill (a cordless drill works just fine) and a ~3. Navigate back to the Octoprint terminal and run the FIRMWARE_RESTART command to restart the printer firmware and load the new config file.

Artillery Sidewinder X1 Review | 3D Print Beginner

Fortunately, if you already have an assortment of metric screws available, you might already have most of what you need for this mod! You can also check out the Trianglelab Matrix Extruder which is capable of similar printing performance and it’s a good alternative to the Wind if you are looking for a Hemera-like extruder. After you install Klipper on Sidewinder X1, there’s also the added benefit of being able to edit the firmware without the need of re-compiling and flashing the firmware. I used a small 10 mm piece of PTFE which perfectly mates the end of the heat break with the BMG Aero.If your main TFT cable is full of glue like mine, you can just remove this wire and continue with the firmware flashing. I would also love to hear back from you with thoughts about the BMG Wind after you tested it for a while.

Artillery 3D

In the future, i also plan to add some sort of brace to the frame, to make it more stiff and allow for higher speeds. To remove the roller wheel posts, use a wrench or pliers to hold the nylon locknuts above each carriage, and use a hex key to unscrew the bolt from below. It’s made from the heatsink part machined from aluminum and the second half made from translucent plastic which is probably the same used in the NF-BMG extruder.I contacted Creality support in the past, and received a reply after a few days, but EVNOVO support was really fast. Artillery developed a 32-bit mainboard, which is characterised by its high stability, powerful computing power and great expandability.