FixtheBog 20mm MDPE Outside Tap Kit With Plastic Wall Plate & Garden Hose Fitting DCV

Product Information

If it’s not possible to install an outside tap, another way to provide a water source would be to install and use a water-butt. This is a great way to capture and store water, no just because rainwater is pretty readily available in the UK, but also because it is free! Once you’ve made it through with the small drill swap for the large bit and then re-drill the hole from the inside. Once about half way through, go outside and drill out the rest of the hole. As said, this will prevent the large drill bit blowing a huge chunk off the face of the outside wall. Step 4 – Fit Isolation Valve and Drain Plug Cut a few lengths of pipe. I cut three: one to come out from the cold pipe, one to feed up to the isolation valve and one to carry up to connect to the hose union. Cover the area with dust sheets and then pop the 8mm bit in the drill and position the tip on the drilling point and start drilling. Don’t force the drill bit into the surface too much, let the drill do the work. If you want to use the supplied old-type hose connector, you will need to force your hose pipe onto the connector and fit a hose (jubilee) clip on and tighten it with a screwdriver. How to Fix a Dripping Outside Tap

Outside Taps for Garden and Outdoor - Stevenson Plumbing Outside Taps for Garden and Outdoor - Stevenson Plumbing

Always start with a small drill first to drill a pilot hole as this takes the strain off the drill trying to drill too large a hole in one go and also when it busts through the wall on the other side it doesn’t blow a huge chunk off. Yes. Basically, you can fit an outside tap anywhere. You just need to be able to run a cold water pipe to it. Outside taps are normally fitted on the outside wall behind kitchen sinks but can be fitted anywhere. How long does it take a plumber to fit an outside tap? The easiest way to make a sleeve is by using a length of 22mm plastic or copper pipe cut to the depth of the hole and then pushed through.

🍪 About Cookies on our Site

pipe connectors (I used a T shaped Speedfit connector and two elbow connectors) and pipe inserts if you’re using plastic pipe For this example we are going to use copper pipework and compression fittings and a standard wall plate for the tap. Diagram for Fitting Outside Tap

Outside Tap Kits - Stevenson Plumbing Outside Tap Kits - Stevenson Plumbing

The last job to do then is to use a suitable exterior sealant and pump a load of it into the sleeve and around the external hole to seal it up and prevent any draughts or water ingress. Do this on the inside also. With the pipe cut, unscrew and remove the compression nut and olive from the end of your compression fittings and slip them over each end of the cut pipe, cap first and then olive and then wiggle the fitting body over each end of the pipe. To make sure you have a good supply of water to your water-butt connected system it is a good idea to collect water from any available sources such as gutters and down pipes from your house and any sheds you may have. He incorporated Housewarm Ltd. in 2011 to provide heating and plumbing services to homes in Newcastle upon Tyne, England. I turn off the hammer function on the SDS drill when I only have an inch or so to go and use it in drill-only mode.

Connect your pipes

A drill and a 20mm drill bit (it doesn’t need to be 20mm exactly, but the pipe that needs to pass through the wall is 15mm wide so make sure it’s bigger than that) In this case, the water carrying pipe (e.g. the pipe running from the supply to the tap) should be allowed to expand and contract naturally through temperature change without fear of erosion or puncture due to it expanding and rubbing on the rough masonry. The most common place is behind the kitchen sink, you can normally connect to the kitchen tap pipe. During the colder months of the year, the chance of the temperature dropping to the point of freezing is quite high and as you probably know, when water freezes it expands. Depending on the length of pipe you will also need to add some pipe clips to hold it firmly to the wall. Step 8 – Fix Tap In Place and Test

Tap Kit, Cut in Tap, Connects to Existing Complete Garden Tap Kit, Cut in Tap, Connects to Existing

Replacing an outside that has already been fitted is very easy and I would definitely recommend a DIYer to give it a go.

Be First to Comment

Summer’s nearly here (woohoo!) and with that, there are so many more reasons to hang out in the garden. If you don’t have an outdoor tap, it can be a real pain to clean in the garden, water plants, even fill pets’ water bowls. I fitted a garden tap yesterday. Before that I needed to attach a hose to the kitchen tap and run it out the window – not ideal! The outdoor tap took just half an hour to fit and is going to get so much use. Read on to follow the steps.

Outside Tap Kit With Plastic Wall Plate and Garden 25mm MDPE Outside Tap Kit With Plastic Wall Plate and Garden

There are no outside tap kits that use everything I like to use, but if you can make it work then go for it. My Outside Tap Kit List Each installation is different and as we have mentioned, will allow you to use a range of different fittings and techniques so take a look at our projects on how to join copper pipes by either using compression joints, or you can use soldered joints if you’re handy with a soldering iron or you could even use SPEEDFIT® plastic piping and joints. When running a water pipe or indeed any object through a wall you really should run a sleeve through the hole first and then run any pipes or similar through the sleaving.

However, the connection does not have to be made under the sink, as long as it’s a cold water supply at mains pressure, that’s all that’s needed. Don’t be tempted to feed an outside tap from water coming from a cold water tank as this will seriously affect cold water availability in the home. You can use brass or plastic hose connectors but brass ones are better. Outside tap fitted with new hose connector As it’s highly unlikely that you’ll use the tap anyway through the winter months, this is certainly the best choice. Alternatives to Fitting Outside Taps The most common way of connecting this to the water supply is to add an elbow to the copper pipe coming from the outside tap using a 15mm brass compression elbow or Speedfit. There is usually a tangle of waste pipes and hot and cold water feed pipes under the sink which make connection of an outside tap difficult so in many cases it may be easier to look between the units, or even behind them to source a cold water feed to the outside tap which is a little easier to work with.