Joined in 2023 
82 
63 About this deal
You will feel when you will know about it that connecting the IDE hard drive to the SATA motherboard is a very easy task. It will take at most 10-20 minutes. Remember that the computer must be unplugged from any electrical connection. While it is possible to make the necessary changes if drivers are required to run that type of drive it is a lot of messing around. Also if Windows has been loaded for more that 12 months it’s better to do a Clean Install so you can get rid of all the crud that clogs up the Registry.
IDE is the short form of ‘Integrated Drive Electronics’ which is actually an interface for connecting the processor and the drives. It should be clear, by interface I mean the way in which your computer and the hard drive is connected. This is also known as ATA or Parallel ATA. On each drive, IDE has its own controllers. So the drive can connect directly to the motherboard. The hard drives which have IDE connection have 8-pin or 24-pin connection usually that plugs into a slot on the motherboard directly. What is SATA? The wide wire in IDE cables caused airflow problems inside the case. The narrower SATA cable allows free airflow inside the case. You have to install the hard drive into an open hard drive area or bay. This depends on the type of computer case. It usually requires just a little sliding into an open bay and normally a very simple procedure. I personally feel that you should not ask this question at this moment of reading. After reading the advantages of SATA, you should know it by now why you need to connect to SATA. In modern times, there is no competition of SATA with IDE; SATA is always ahead of IDE.Under Device Manager, look for specifications in storage menu. If it says S-ATA or Serial ATA, it’s SATA. For IDE devices, it can say EIDE or just IDE. Summing Up SATA (right) and IDE (left) hard drives. The SATA hard drive has the data cable on the right and power cable on the left. The IDE data cable is ribbon-like (on the left) Hard drives need a cable/connection for data and one for power. Parallel ATA only allows data cable lengths up to 18 in (457 mm) while SATA allows cable lengths up to 1 m (3.28 ft). eSATA cables can be 2 m in length. The SATA cables are up to 40 inches. So it is an advantage of SATA over IDE which is the management of cables and length of the cables connecting the hard drives and motherboard. When you have extra length in cables, more flexibility of the positions of the drive can be attained.
IDE Hard Drive: It is one of the most elements that’s needed. You know by now what IDE is. IDE hard drives are easily identifiable through their pin connection points usually. In most of the cases, the installation is by plugging it into the required component. It is needed to ensure a tight connection. There are four to six SATA connections usually in a normal motherboard which allows multiple SATA hard drives to hook up. Moreover, the total switch from IDE to SATA doesn’t happen without issues sometimes. If you have an IDE hard drive but have a SATA motherboard, you can connect the drive to the motherboard still. This may be your reason for the conversion of IDE to SATA. Connecting the IDE Hard Drive to SATA Motherboard SATA motherboard: As you know, SATA is the current standard for the connection of hard drive to the motherboard. This is obviously a replacement for the previous IDE connection. It is easily identifiable by the simple plug with only one connection point. SATA motherboards are more likely the present standards and are more efficient, faster, and more stable. Data transfer speed for IDE ranges from 5MB/s up to 133MB/s (ATA100/133). The parallel wire transfer mode reached its limit with the speed of 133 MB/s.
IDE To SATA Converter
The data transfer rate of SATA connections is very fast compared to that of IDE connections. In fact, the main reason for SATA being used over IDE is because of the increased data transfer speeds of SATA connection hard drives. IDE has the capacity of data transfer speeds of 33/66/100/133 MB/second, whereas SATA is capable of 150/300/600 MBs/second. The differences in speed are due to the various versions and flavors of IDE and SATA. SATA consists of an 8 mm wide wafer connector on each end and the cable has a 7-pin connector, 3 grounds and 4 active data lines in two pairs. It has the facility to attach only one drive and so Serial ATA does away with Master/Slave configurations. It may even work with a SATA Drive but not a SSD Drive as while these days they are interchangeable in the past they where not always so. Also the hardware always treats IDE Drives as the Default Master Drive and writes the Boot Loaded to that Drive so it’s important after the Clone to remove the IDE Drive before starting the system on the SSD Drive.
As for the TRIM I’m really not sure how it would impact with a SSD Drive it really all depends on the ChipSet of the M’Board. SATA took off where ATA stopped as far as speed is concerned. The first generation of SATA was 1.2 Gbit/s (150 MB/s; note that MB is mega bytes and Gb is giga bits) similar to PATA/133. Today the third generation of SATA (3.0) (released on May 27, 2009), 6 Gbit/s (600 MB/s) hard drives and motherboards are being used. Just my opinion though but look in the BIOS and see if there is an Option to make a SATA Drive the boot drive as that would remove the need for a Driver. Yes, SATA is faster than IDE. It is the newer standard and should always be chosen over the older IDE connectors. While IDE offers data speed of up to 133 MB/s, SATA can transfer data at 6 Gb/s. Can a USB to SATA power a HDD?SATA has also done away with the master/slave configuration (technically, device 0 and device 1) used in IDE drives. With PATA (IDE), attaching two hard disks to the same channel required one to be set to be the master, the other the slave. For hardware, this usually meant setting the right jumper settings. Firstly, open the external part of your computer or your computer case to get access to the motherboard and the hard drive connections. You may need a screwdriver or may not need The SATA drives usually need very little power than PATA drives. The SATA drive usually uses only 250 mV of power, which is even 25 percent of one volt. Great, Now we have a formatted SATA drive and a partition for OPL ready for games. Game Installation SATA drives have an additional feature of Hot plugging which mean that even as the computer is running drives can be removed or added.
In a computer system, it's possible to have more than one harddrive. To connect multiple IDE drives, you need to chain the ribbon cables from one to the next. The computer system has no idea which is the main drive, from which to load the OS. The main motivation behind the creation of SATA was the increase in the drive speed. For, SATA connection hard drives are very fast. Advantages of SATA
About the Author
But the SATA bus is a serial point-to-point bus, which means only one device can be connected on each channel. Many SATA drives can connect to the motherboard via multiple ports, and the drive to boot from is specified in the BIOS settings. After many days of IDE connection hard drives, there came the SATA hard drives which are meant to replace the IDE hard drives for their more efficient characteristics. SATA means ‘Serial Advanced Technology Attachment’. The main characteristic which differentiates SATA from PATA or IDE is that in SATA the information moves between the hard drive and motherboard as serial one, i. e. one bit after another.
Great Deal 
New Comment