276°
Posted 20 hours ago

Ubiquiti Networks UAP-AC-LR 175.7 x 43.2 mm 2.4-5 GHz 802.11ac Dual-Radio Long Range - White

£9.9£99Clearance
ZTS2023's avatar
Shared by
ZTS2023
Joined in 2023
82
63

About this deal

wWell, in this case, I would indeed start over. It’s hard to tell what went wrong. Leave the ERX as it is, the problem is most likely in the access point configuration. Reset the Unifi Controller and the access points. Start with one access point, set up the network to your liking and test it. If it’s stable and working as it should, add another access point. Test it again to be sure. That’s the best way to find any potential problems. I have a problem discovering the APs, I mean I connect them properly to the PoE switch, and the configuration on the switch is also the rigth one to reach the Controller. The Aps have being reset to factory values, but the system doesn´t recongnize them. You could enable client isolation, that would help a little. Better is to use vLANs for this, but you will need to set it up from the router through the switch and in the accesspoint. I could not connect to these wifi networks (using samsung galaxy S9+ to test) so I disabled them in Unifi. Still, getting connected to the Basement AP is not possible on the main WIFI network (not a vlan). on other AP’s the S9+ is connected, but every few minutes it seems to disconnect and not to reconnect again, only manually.

all devices have latest firmware. 3 AP’s are on an HP switch, one is directly connected to the EdgeRouter X. Since these devices were already installed by someone else, we have no idea what the account credentials are, if any.

System Requirements

I have used Access Point AC Mesh units is such situations. Put the unit inside with one of the supplied antennas and use a small yagi outside pointed at the existing WiFi network. Connect the antenna and AP with a suitable cable. The quoted wireless specification is given as the maximum radio performance. Achievable range and throughput will vary depending on the regional regulations where the radio is deployed. Airtime Fairness: Minimises problem-client effects on system performance by limiting their airtime access

The second method, the UniFi Controller Software Reset is also a fairly simple process; For this to work, you must have the UAP adopted by the UniFi Controller Software: Probably the easiest way to solve this is by adding the AP to the VLAN10. But I don’t think that is the cleanest option. I have seldom come across such a well written article. Most I.T. professionals have technical skills, but their writing skills leave much to be desired. Well done Ruud. Thanks for clear and precise instructions. You can adopt the access point into your controller, but you will need to open the correct ports in your firewall so the access point can access the controller. Another option is to use cloud controller Make sure that you have Java11 JRE installed on your device. If you don’t have it installed, then the installation will warn you about it. Step 3 – Install Unifi ControllerAbove was tested on a Ubiquiti UniFi UAP-AC-PRO and to the best of my recolections works. The last step may have some inaccuracy as I wasn’t taking notes but seemed straighforward, especially compaired to the previous steps..)

The exception is in the weakest signal Location F, where the WAP321’s downlink throughput is more than 2X and the WAP121’s is almost 4X running uplink. Does the access point project my network if I don’t do anything other than plug it in to my lan (through the POE)? In other words, can I use it to function essentially as an extender without any configuration? The AC-Pro has 3×3 MIMO antennas to get that high network speed, but to use it, your endpoint (notebook, smartphone, TV) must also be able to handle it. So if you are after maximum speed and you have a notebook that also supports a 5ghz network at 1300 Mbps, then you should go for the AC-Pro. Designed for Optimal RF Performance - The newly redesigned UniFi Controller optimises RF performance:Yes, you can set the minimum RSSI level on the access point. This will require the client to have a minimum signal strength when connecting. Basically I use my computer and my smart tv hooked up right now only to my edgerouter 4 max this product

Asda Great Deal

Free UK shipping. 15 day free returns.
Community Updates
*So you can easily identify outgoing links on our site, we've marked them with an "*" symbol. Links on our site are monetised, but this never affects which deals get posted. Find more info in our FAQs and About Us page.
New Comment