Swing Hammer Swing! (Vintage Classics)

Product Information

Besides the brogue, the unusual, imaginative language is tremendous – a work of art. It’s filled with humor and irony. Some passages I liked: Ball Peen: The head of this hammer has a flat face on one side and a round, somewhat ball-shaped face on the other. There is no claw. Ball peen hammers are mostly used for metalwork. Most homeowners can stay away from specialty hammers, such as the 20 to 30-ounce ripping-claw framing hammer, though this hammer is often used to drive concrete nails. Those are for pro carpenters or very experienced DIYers who are doing a lot of rough-carpentry work or demolition jobs. Framing hammers look similar to standard claw hammers, but the claws are straighter, the handle is longer, and the head is considerably heavier. Along with fast deliveries & top quality, the buyer’s specific preferences are always of great concern, and that concern is magnified when the buyer’s preferences are found to be individually unique & special.

Generally, there should always be these key-movements, but the ROM and velocity of their actions will vary. The variability will differ for a baseball pitcher, whose body actions should not change while their arm slot should—elbow and wrist actions are based on the type of pitch and the location they are trying to throw. Closing Thoughts

If you find that your nails are splitting the wood (most common with narrow pieces of hardwood lumber), try blunting the tip of the nail before driving it. Wood splits because the fibers are bent and deformed as the nail forces its way between them. A blunt nail tip tends to sever the wood fibers rather than bend them, so the nail is less likely to split the wood. Be aware, however, that the holding power of the nail is slightly reduced with this method, as it can't be gripped as tightly if the wood fibers are severed. When it comes to weight, the Stubby is just right; at 12 ounces, it isn't too heavy, nor is it too light. The steel head is strong enough to survive repeated abuse for long projects, while the weight is convenient for the times you need a little extra force in your swing. At an overall 8 inches in length—the typical hammer has a 10-to-12-inch handle, plus the length of the head—it is also a perfect size for carrying around on your tool belt when not in use.

Club: Also called "drilling hammers," these short tools with two flat faces are basically smaller sledgehammers. Club hammers are great for light demolition, as well as driving chisels and wedges. Wood is the classic hammer handle and is still preferred by many. It’s fairly lightweight, doesn’t transmit a lot of vibration to your hand and wrist, and with enough use, wooden handles tend to “form” a little bit to your hand over time. Still, wooden handles are the likeliest to break, and they can be slippery. They’ll also rot or warp if left out in rough conditions or exposed to moisture. However, you can generally replace a wooden hammer handle if it breaks. His novels draw on the changing face of modern Scotland. Swing Hammer Swing (1992) was set during the demolition of the old Gorbals. It took 30 years to write. [1] The Devil's Carousel (1998) drew on the decline of a fictionalised version of the Rootes/Chrysler car plant at Linwood. Torrington worked there for eight years, as a telex sequencer, before the plant's closure. [2] A hammer that weighs too much will tire you out. However, go too light, and you sacrifice strike power. Note that a hammer’s weight refers to just the steel head, not the entire tool. Torrington's first published stories appeared in newspapers. [1] He later attended a Paisley writers' group set up by James Kelman [3] and a creative writing group in Glasgow associated with Philip Hobsbaum, which also included Kelman, Tom Leonard, Liz Lochhead, Alasdair Gray and Aonghas MacNeacail.Rubber Mallet: Shaped much like a club hammer, but with a rubber head instead of metal, mallets are not used to drive nails but to add some force when driving stakes or chisels, building furniture, working with upholstery, or similar tasks where you need more power than your hands provide alone, yet you don’t want to damage the surface upon which you are working.