Ubiquiti Networks RJ45 10Gbps Transceiver Module SFP+ to RJ45 UF-RJ45-10G (SFP+ to RJ45)

Product Information

A GLC-BX40-D-I or GLC-BX40-DA-I device connects to a GLC-BX40-U-I device with a single strand of standard SMF with an operating transmission range up to 40 km. The Cisco 10GBASE-LR Module supports a link length of 10 kilometers on standard Single-Mode Fiber (SMF,G.652). The Cisco 10GBASE-LRM Module supports link lengths of 220m on standard Fiber Distributed Data Interface (FDDI) grade Multimode Fiber (MMF). To make sure that specifications are met over FDDI-grade, OM1 and OM2 fibers, the transmitter should be coupled through a mode conditioning patch cord. No mode conditioning patch cord is required for applications over OM3 or OM4. For additional information on mode conditioning patch cord requirements please see: https://www.cisco.com/en/US/prod/collateral/modules/ps5455/product_bulletin_c25-530836.html. When shorter distances of Single-Mode Fiber (SMF) are used, it might be necessary to insert an inline optical attenuator in the link to avoid overloading the receiver. A 10-dB inline optical attenuator should be inserted between the fiber-optic cable plant and the receiving port on the SFP at each end of the link whenever the fiber-optic cable span loss is less than 8 dB. The 10G RJ45 SFP+ module is widely used in 10 Gigabit Ethernet, typically for data center interconnect (DCI) between a switch and NIC. We know that the fiber 10G SFP+ transceivers, and high-speed cables can also achieve 10GbE DCI connectivity. Given that 10G transmission over copper link has the cons of higher latency, more power consumption, and short reach limitations than optical link, some may ask: what's the purpose of the 10GBASE-T SFP+ copper module?

Cable Internet" is a consumer term that typically refers to transmitting data via a coaxial cable using a version of DOCSIS. An SFP module will typically present itself as a little box that you insert into a switch or router. You then connect fibre or copper cables to the SFP module using one of the standard connectors. Optical interoperability with 10GBASE XENPAK, 10GBASE X2, and 10GBASE XFP interfaces on the same link As @JourneymanGeek points out, Ethernet specifies what signals to transmit and receive, and puts requirements on the characteristics of the cable - certain signal loss is acceptable at certain frequencies, and certain inter-pair cross-talk levels (where the signals on one pair can be " heard" on another pair). Ethernet (like DOCSIS) outlines the signals and cable requirements, but it also outlines options for the connectors used.The Cisco 10GBASE-ER Industrial Temperature Module supports a link length of up to 40 kilometers on standard Single-Mode Fiber (SMF, G.652). The SFP-10G-ER-I for Industrial Operating Temperature Range is a multirate 10GBASE-ER, 10GBASE-EW and OTU2/2e module. The Cisco 10GBASE-ER module supports a link length of up to 40 kilometers on SMF (G.652). SFP-10G-ER-S does not support FCoE. Ethernet is a set of standards ( IEEE 802.3) which covers transmitting data via coaxial cable, twisted pairs as well as fibre.

Information about Cisco’s environmental sustainability policies and initiatives for our products, solutions, operations, and extended operations or supply chain is provided in the “Environment Sustainability” section of Cisco’s Corporate Social Responsibility (CSR) Report. The GLC-GE-DR-LX SFP can interoperate with other 1G SFPs/interfaces as long as those are based on 1000BASE-LX/LH standard. No attenuator is needed in any fiber strand.However, they do exist as "Direct Attach Cables". In this form, the modules are attached to either end of the cable, and are not designed to be removed. The SFP-10G-BX40D-I and SFP-10G-BX40U-I SFPs support Digital Optical Monitoring (DOM) functions according to the industry-standard SFF-8472 Multisource Agreement (MSA). This feature gives the end user the ability to monitor real-time parameters of the SFP, such as optical output power, optical input power, temperature, laser bias current, and transceiver supply voltage. Hot-swappable input/output device that plugs into an Ethernet SFP+ port of a Cisco switch (no need to power down if installing or replacing) Accidental Damage-Additional Information: Accidental Damage Service excludes theft, loss, and damage due to fire, flood or other acts of nature, or intentional damage. Customer may be required to return damaged unit to Dell. Limit of 1 qualified incident per contract year. For more information, consumers visit Accidental Damage Service Contract (Consumer) or commercial customers visit Accidental Damage Service Contract (Commercial).

Copper SFP+ module is designed with an RJ45 connector that works with copper Twisted Pair Ethernet cables. Copper cabling costs less than fiber cabling. For data center network professionals, the power consumption of active devices is very important. After all, every watt consumed by a device means that two additional watts are needed to cool the data center. Take FS SFP+ copper solution as an example, its power consumption is 2.5W or less, and the longer the length, the lower the power consumption of the 10GBase-T modules. SFP+ to RJ45 Solution: Pros and Cons Pros DOCSIS outlines requirements for the signals and cable, but I don't believe it dictates the termination / connectors. In the UK these are typically terminated with F-Type Coax connectors.The Cisco SFP-10G-SR-I is a multirate 10GBASE-SR, 10GBASE-SW and OTU2/2e module for industrial operating temperature range. This module also supports CPRI datarate options 3, 4, 5, 6, 7, 7a, 8. It supports a link length of 26m on standard Fiber Distributed Data Interface (FDDI)-grade Multimode Fiber (MMF). Using 2000MHz *km MMF(OM3), up to 300m link lengths are possible. Using 4700MHz *km MMF (OM4), up to 400m link lengths are possible. Twisted-pair cables consist of two conductors of a single circuit twisted together, which reduce the effects of EMI and mutual interference between pairs and improve electromagnetic compatibility. Nowadays the cables are shielded with aluminum foil to increase protection against crosstalk on neighboring lines. There are Cat5e, Cat6, Cat6a, Cat7, Cat8 Ethernet cables that can be used in your network solution. And this 10Gb copper SFP+ solution can be paired with Cat6a/Cat7 or Better for a transmission distance of 80m. Latency The GLC-BX-D-I and GLC-BX-U-I are the Industrial temperature rated (IND) counterparts of GLC-BX-D and GLC-BX-U SFPS. This allows link operation in harsh environmental conditions where the module case temperature can be in the range -40°C to 85°C. The SFP-10G-BXD-I and SFP-10G-BXU-I SFPs also support Digital Optical Monitoring (DOM) functions according to the industry-standard SFF-8472 Multisource Agreement (MSA). This feature gives the end user the ability to monitor real-time parameters of the SFP, such as optical output power, optical input power, temperature, laser bias current, and transceiver supply voltage. The term " Ethernet cable" is somewhat of a misnomer. You will likely actually be referring to a CAT5, CAT5e, CAT6 or maybe CAT7 cable that is terminated with an RJ-45 on either end. If terminated correctly, these can be used to connect two Ethernet devices that have a common set of supported protocols.