276°
Posted 20 hours ago

Magnetic Wire Pulling System KLEIN TOOLS SRS56037

£9.9£99Clearance
ZTS2023's avatar
Shared by
ZTS2023
Joined in 2023
82
63

About this deal

The maximum energy product of a magnet is measured in Mega Gauss Oersteds (MGOe).This is the primary indicator of a magnets ‘strength’. In general, the higher the maximum energy product value, the greater the magnetic field the magnet will generate in a particular application. While using hot water or blow dryer won’t do much alone, it can definitely be of assistance when dealing with dents. Warming up your car’s body will make it easier to give shape and mold the bodywork. If you can’t seem to pull a dent out, try blow-drying the area or spraying it with warm water. We recommend blow drying because you would need a large amount of hot water to warm the car enough. Never use an open flame on your vehicle. 4. Can I fix the dent myself, or do I need to get professional service?

The very first thing you need to do, no matter which kind of dent puller you’re using, is to prepare the surface of your car. The piece of car body you’ll be working on should be clean, so that the puller can get a proper grip of the surface, making your job easier.

CATEGORIES

Magnetic wire pullers are a game-changer in the world of electrical installations. Have you ever struggled with routing wires through tight spaces? A magnetic field can be visualised as magnetic field lines passing through a magnet along its direction of magnetism. The field strength corresponds to the density of the field lines over a given area. The total number of magnetic field lines penetrating an area is called the magnetic flux density.

If you use the dent pullers in accordance with the user manual, there’s hardly any chance you’ll damage the vehicle. If you are much stronger than an average person, pay attention not to put all your might into pulling, since you may pull too hard and create a bulge. The only thing we’d recommend, especially if you’re working with a glue-based dent puller, is to have a bit of car paint polish to fix any scratches that may appear after scraping away the glue. After polishing, always apply top-rated car paint sealants, and afterward, a top-rated car wax.

Scrabble Tools

Once you’ve removed the excess glue, it’s time to reapply glue and start again. 3.4. After treatment There are a couple of things you should consider before giving up on DIY fixing and going to a professional. Remember that professional service can be quite expensive, so you’re only better off going to a repair shop if one of the following is true: Open circuit flux densities can be measured using a Gauss meter and hall probe. Open circuit flux densities for neodymium magnets rarely exceed 6,000 Gauss, but because neodymium magnets have a straight line demagnetisation curve, the flux density will rise when the magnet is immersed into a circuit and the distance between north and south is reduced by the introduction of steel. The flux density can therefore rise from the open circuit value to almost the remanence value. PULL STRENGTH

Dent pullers come in a variety of shapes and modes of use. Even though they all essentially do the same job, the different types of dent pullers don’t look remotely alike. They also all use different methods of grasping the surface of the vehicle body. Let’s go through the different types of dent pullers, so you can figure out which suits you best. 1. Suction Cup You take matters into your own hands and fix the dent for a fraction of the price it takes to do it at a shop. Maximum energy product, remanence and coercivity can all only be measured with a hysteresis graph testing machine which plots a second quadrant hysteresis curve. .

Specification

When attaching the suction cup, you need to make sure that it covers the area of the dent completely. Push the suction cup in until you feel it grasped the surface firmly. A magnetic wire puller is a tool used to route wires through walls, ceilings, or confined spaces. It uses a magnet to guide and pull wires, making the installation process easier and less time-consuming, especially in tight or hard-to-reach areas. So, when selecting a magnet, the key things to look out for are the maximum energy product value of a magnet, the open circuit or surface gauss value and the maximum pull strength. These three attributes allow you to compare one magnet against another. Once your glue is liquid, it’s time to apply. Put a dab of glue onto either the plastic tab of the puller or the dent itself. Don’t put too much glue since that can weaken the grip. You need somewhere around a pea-sized drop of glue for every 0.5 inches of the tab.

Asda Great Deal

Free UK shipping. 15 day free returns.
Community Updates
*So you can easily identify outgoing links on our site, we've marked them with an "*" symbol. Links on our site are monetised, but this never affects which deals get posted. Find more info in our FAQs and About Us page.
New Comment