Nartel® 10 X 1 AMP SHAVER FUSES BS646 1AMP MINI FUSE 20MM X 5MM

Product Information

Plugwash's final suggestion is the one to go for - just change the plugs on your appliances and have done with it.

Nartel® 10 X 1 AMP SHAVER FUSES BS646 1AMP MINI FUSE 20MM X 5MM

Once this is done, a minor works certificate is then issued to prove the installation has been carried out correctly.If either of the above are ignored, if any issues occur and you cannot produce a certificate for the works then there is a good chance that your home insurance will be invalid, so it certainly isn’t worth the risk.

Fitting an Electrical Shaver Socket | DIY Doctor

Zone 2 – the area beyond zones 0 and 1, 0.6m horizontally and up to 2.25m vertically. Zone 2 also includes any recessed window with a sill next to the bath and also around the wash basin Ideally look for a model with double wound isolating transformer, integral overload protection and shutters on the plug inlets to prevent any accidental splashing. You have to be particularlly carefull with the german/dutch schuko plugs because they use side clips not pins for earthing. This means it is easy to end up with a situation where an appliance that needs earthing for safe operation has it's live and neutral pins connected but not it's earth pins. In this example here we are using an existing lighting circuit so a 1mm twin and earth cable is run out from the top of the ceiling rose, down through the ceiling and down a chase that was cut into the wall. However if you are installing in an upstairs then you may be able to locate a suitable supply in the loft. This is often the easiest route as everything should be much more accessible.

Should a Shaver Socket be Connected to a Fused Connection?

As previously mentioned, if you are sing a lighting circuit make sure it’s RCD protected. If it isn’t then you can’t use it. visitor adaptors (e.g. http://www.roamingfox.co.uk/UK-Visitor-Travel-Adapter-pr-16228.html ). Theese have a higher current rating than shaver adaptors and can be used with some earthed plug types. However THEY WILL NOT PROVIDE AN EARTH TO GERMAN/DUTCH/FRENCH plugs. Zone 1 – the area directly above zone 0, limited vertically to 2.25m above the bottom of the bath or shower, also 1.2m horizontally from the centre of a shower outlet to the height of the outlet, or 2.25m whichever is the higher

Shaver Plug Adaptor, UK 2 Pin to 3 Pin 13A Fuse LENCENT Shaver Plug Adaptor, UK 2 Pin to 3 Pin 13A Fuse

All wires are then set into the wall and capped with protective sleeving and then all chases are filled, smoothed off and the either painted or tiled over. The cable is then normally capped (covered with a protective UPVC capping) or run through some UPVC trunking/pipe to protect it and hold it in place.The cable was then secured in place using UPVC capping to not only hold it but also protect it from any damage that might from any potential future work. If no supplies are this conveniently placed then it may be that you have to take up some floorboards in an above room and run your supply from here. There are many types of adaptors on the market and knowing what is suitable for what purpose is important to get a safe and reliable result.

Basics - Plugs and Adaptors - Portable Power - Masterplug UK

As we have mentioned above, when running down a wall to a power supply unit such as this the cable will need to run vertically down in a straight line to comply with regulations. Unfortunately most stores only carry the first two categories and often provide poor information about what they are suitable for Hard to see how that's true, as shaver plugs and standard 2-pin continental mains plugs have different spacing. Yes you can force them in but I'd not agree that makes it "suitable". It seems indeed to be the right conclusion to cut and replace the Euro (schuko) earth plugs to British ones alltogether.And that means that you should not replace the fuse or use it for anything which draws more than 1A.