Joined in 2023 
82 
63 About this deal
Below the consumption chart are a variety of Shelly Device measurements. Observe the Eco (compared) value that gives a percentage of how much lower the consumption value is. In addition, also observe the total consumption value in kilo-Watt-hours (kWh), the average consumption in Watt-hours (Wh), and the maximum and minimum consumption in Watt-hours (Wh). Change the current channel name. This will reflect on the device name in the application if the “Sync name” application setting is enabled. Firmware Update
Connect a jumper wire from O on the Shelly to L1 on the switch (note leave the existing L1 wire in place)
Reduce the energy consumption of your device by lowering the CPU frequency and modem activity. Enabling Eco Mode can help you conserve power and extend the battery life of your device. I mentioned, that Shelly 1L caters to both wiring standards. You can use the same device in the control boxes with no-neutral and live & neutral configurations. There is a catch. While the L&N configuration is pretty straightforward, the no-neutral installation comes with additional limits: Eagle-eyed readers will notice that Shelly 1L supports 2 switches. These can be configured independently and set to various modes including push, toggle, and edge. What’s also new are the default power state modes that include the current state of the physical switch 1 and 2. Pretty handy for detecting switch changes made during a power outage. Toggle Switch: Set this Relay to be "Toggle" switch. Act as a flip switch with one state for "ON" and one state for "OFF".
Shelly 1L has an embedded Web Interface which can be used to monitor and control the device, as well as adjust its settings. Main applications Configure the actions for your device - enable, disable, add duration and URLs. Settings POWER ON - DEFAULT MODE When dealing with wall outlet (high) voltages you should satisfy yourself that whatever you are doing is safe and if unsure, seek advice from someone who is sure.This time I want to look at the Shelly 1PM and a newer product, the Shelly 1L. I’ll mention in passing that when the devices arrived, they included my favourite type of old-school electrical screwdriver – thanks, The company are called ALLTERCO Robotics and are based in Sofia, Bulgaria.
SNTP synchronizes your device's system time with a server that has already been synchronized by another source. There is already a set server, which is the default one - http://time.google.com, however if there are any problems, you can easily change it and enter a new one in the text box. Changing this setting will reboot the device. ADVANCED - DEVELOPER SETTINGS A Shelly 1L can work with or without no-neutral wiring, making it ideal for placing behind a light switch to make it smart. The 1L has a lower maximum load of 4.1A and can only be used with AC 110-230V ±10%, 50/60Hz Comparison
Shelly 1L module specification
I had attempted to install the Shelly 1L at the same location as Switch A, leaving the wiring as it was in the wall box for Switches B + C. I have since uninstalled the Shelly and so have not got a photograph of the device installed. However, the diagram below shows how I intergrated it with the existing circuit: Connecting your Shelly to its cloud allows you to control it remotely, receive notifications and updates about your devices. The default for this setting is for the cloud to be enabled. If you disable the device cloud support, you will lose connection to your device from outside its local network! I/O URL Actions Tartalom személyre szabása Ezek a sütik lehetővé teszik számunkra, hogy az Önről rendelkezésre álló információk alapján tartalmakat és hirdetéseket jelenítsünk meg Önnek, hogy a lehető legjobban ki tudjuk elégíteni az Ön igényeit. Ez legfőképpen ahhoz kapcsolódik, hogy milyen tartalmat tekintett meg, illetve milyen eszközzel lépett be az oldalunkra. To clarify the steps (which in some ways is much easier to comprehend than interpreting the diagram):
Great Deal 
New Comment