HP J9775A 2530 Series Blade System Network Switch Module (48G Port, 4 SFP Slots)

Product Information

autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only

RJ-45 autosensing 10/100 PoE+ ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3at PoE+); Media Type: Auto-MDIX; Duplex: half or full RJ-45 10/100/1000 端口（IEEE 802.3 类型 10Base-T；IEEE 802.3u 类型 100Base-Tx；IEEE 802.3ab 1000Base-T 千兆位以太网）或 SFP 插槽（用于 SFP 收发器）

For J8705A and J8706A modules: All (for J9054B/C 1990-3613); K.15.08.0007 (for J9054C 1990-4112 and 1990-4483) J9054D: K.15.08.0007

The YA.16.08 (generically the 16.08) is the cutting edge and it includes all the new features, the most conservative is now the the 16.02...personally I use the 16.05 and the 16.08...but it boils down to what feature you need (16.08 has more feature than 16.07, 16.07 has more than 16.06 and so on...).The Aruba 2530 Switch Series supports a choice of management interfaces with Web GUI, command-line interface (CLI), and SNMP with either console or micro USB ports. For use in the SFP⁠+ ports of the JL075A 3810M switch. Also used in any 3810M switch with a JL083A Aruba 3810M/2930M 4SFP⁠+ MACsec Module installed. For J8705A and J8706A modules: K.12.01 (for J9054B/C 1990-3613); K.15.08.0007 (for J9054C 1990-4112 and 1990-4483) J9054D: K.15.08.0007

It forwards IPv6 multicast traffic to the appropriate interface; prevents IPv6 multicast traffic from flooding the network. IEEE 802.3 类型10BASE-T，IEEE 802.3u 类型 100BASE-TX，IEEE 802.3ab类型 1000BASE-T）；双工：10BASE-T/100BASE-TX：半双工或全双工；1000BASE-T：仅全双工 J9772A, J9773A, J9774A, J9775A, J9776A, J9777A, J9778A, J9779A, J9780A, J9781A, J9782A, J9783A, J9853A, J9854A, J9855A, J9856ASupports Airwave Network Management software to provide common platform for Zero-Touch Provisioning management, and monitoring for wired and wireless network devices. It sets per-port ingress enforced maximums for all ingressed traffic or for broadcast, multicast, or unknown destination traffic. Table 57: Compatibility for SFP copper transceiver modules. The specifications for Revision D transceiver products are the same as the specified Revision A, B, and C SKUs. Not supported for use in the following 3800 models: J9573A, J9574A, J9575A, and J9576A. The SFP⁠+ ports do not support 100M operation.

The 8325 requires configuration of "interface groups" (groups of 12 ports) to enable the use of 1G or 10G transceivers / DACs in the SFP28 ports (default is to use 25G transceivers / DACs). RJ-45 10/100/1000ポート(IEEE 802.3 Type 10Base-T、IEEE 802.3u Type 100Base-Tx、IEEE 802.3ab 1000Base-T Gigabit Ethernet)またはSFPスロット(SFPトランシーバーに使用)ポートとして使用可能 J8177C/J8177D is not supported for use in the Dual-Personality ports of the 2920 Series Switches. For use ONLY in the J9731A module.Power savings with fanless models, Energy Efficient Ethernet (IEEE 802.3az), and ability to disable LEDs and enable port low power mode. Gig LH (J4860C/J4860D) is not supported on the 1850 series. Other 1850 models not listed do not have SFP ports. Now few words regarding the "recommended software version"...actually, as you can see, for your Aruba 2530 (that is fairly generic for the entire Aruba ArubaOS-Switch NOS) there are 5 (five!) current software branches all receiving updates: J8177C/J8177D are not supported for use in the Dual-Personality ports of the 2930M Series Switches.