Drygrip Adhesive: Dryzone System: Re-Plastering Fixative

Product Information

Available in 3 and 5 litre tubs – Coverage rate of 5m 2 per litre – Brush or roller applied Drygrip Adhesive: Internally applied thermal insulation isolates the heated interior from the masonry, which will therefore be cold, producing a risk of interstitial condensation behind the thermal insulation; to prevent that, an AVCL should be applied on the warm side of the thermal insulation. Drygrip Adhesive is applied directly to plasterboard, using a Dryzone High Viscosity Applicator Gun. The adhesive should be applied at regular spacings. The plasterboard is applied directly to a Dryshield treated wall, using positioning plugs to regulate the width of the air gap. The positioning plugs should only be used to adjust the positioning of the board, they do not take any of the structural load. Available in 3 and 5 litre tubs – Coverage rate of 5 m 2 per litre – Brush or roller applied Drygrip Adhesive:

A rising damp and replastering treatment can now be completed in under 24 hours, using the Dryzone Replastering System. All the components of the system have been designed and formulated to create a long lasting and cost effective decorative surface. Components & Coverage Dryshield Cream: Dryzone provided a cleaner, faster and more cost effective treatment for rising damp than fluid pressure injection systems, which were the previous industry standard. This innovation transformed the industry, making damp-proofing creams the default method of treatment. Replace the end cap and nozzle, trimming the end of the nozzle to give a minimum 10 mm diameter hole. In some cases the hole in the nozzle can be made larger to discharge more product during application.Dryshield makes the surface it is applied to hydrophobic and weakens the crystallisation strength of the salts within, or at, the masonry surface. The surface is left breathable, so water vapour can still escape the wall, which allows it to dry out, but salts are not able to build up on the surface and contaminate, or dislodge, any part of the plasterboard. How Dryshield is Applied The Dryzone Express Replastering System is the fast, clean and modern way to replaster a wall after the treatment of rising damp. The system utilises a salt inhibitor cream and a salt & damp resistant adhesive to adhere plasterboard to salt contaminated walls. Following the installation of the DPC, it may be necessary to replaster. Without replastering, dampness and groundwater salts can spoil decoration on the interior walls – potentially causing paint to bubble, plaster to crumble and wallpaper to grow mould. mm × 5.5 mm plastic positioning plugs. They are used to set the air gap between the board and the wall before the Dryzone Adhesive cures.

Salt and Damp Resistant: Drygrip Adhesive offers impressive resistance to salt and moisture, ensuring a strong and durable bond on masonry surfaces. The concept that our laboratory team developed was, in effect, a variation on dot and dab plasterboard application. The idea being that, if plasterboard could be adhered to a wall in such a way that no salts could transfer to it from the wall, the plaster coat could be applied almost immediately. The Dryzone High Viscosity Applicator Gun with Dryzone Nozzle is a versatile tool compatible with both Dryzone DPC Cream and Drygrip Adhesive, providing flexibility and convenience in application. Key Features The product forms a key part of Safeguard’s Dryzone damp proofing system – a complete rising damp renovation range that delivers permanent damp proofing solutions.

Available in 600ml foil sausages, for use with the Dryzone High Viscosity Applicator Gun – Coverage rate of 1 to 2 sausages per 2.8m 2 plasterboard Dryzone Plasterboard Positioning Plugs: In stark contrast, a rising damp and replastering treatment can now be completed in under 24 hours using the Dryzone Replastering System. Each component of the system has been carefully designed and formulated to provide a long-lasting and cost-effective decorative surface. Key Features Drygrip Adhesive is an essential part of the Dryzone Express Replastering System, offering a fast, clean, and modern solution to replaster walls after the treatment of rising damp. This system capitalizes on the effectiveness of a salt inhibitor cream and a salt & damp resistant adhesive to securely adhere plasterboard to salt-contaminated walls. The Dryzone High Viscosity Adhesive Applicator Gun is designed for use with Drygrip Adhesive. Once the foil sausage is pierced and inserted into the main tube, the high-torque trigger mechanism allows for easy application of the adhesive to plasterboard. This tool is also reusable and easily cleanable. Dryzone High Viscosity Applicator Gun with Dryzone Nozzle

An effective salt inhibitor cream, for use on walls contaminated with salts, as a result of rising damp. It resists the formation of salts in, or at, the masonry surface, without the need for a sand:cement render and acts as a primer for Dryzone Salt & Damp Resistant Adhesive. Drygrip Adhesive is a salt and damp resistant adhesive glue Fixes plasterboard to walls without the need for battens or screws. Easily applied with the Dryzone High Viscosity Applicator gun cures to allow plasterboard to accept new plaster after only 1-2 hours. All choices regarding the type of system to use with any individual job, however, should be made with the advice of a professional. Certain jobs may be inappropriate for the Dryzone Express Replastering System, or for certain types of plasterboard. It is important to choose the correct materials and methods for each individual job. Available in 600 ml foil sausages, for use with the Dryzone High Viscosity Applicator Gun – Coverage rate of 1 to 2 sausages per 2.8 m 2 plasterboard Dryzone Plasterboard Positioning Plugs: The adhesive when dry sets fairly hard but there is a small amount of flex in it. Kind of rubbery. Certaibly disent set like cement or normal dry wall.

Why Choose the Dryzone Express Replastering System?

Dryshield Cream is a salt resistant, breathable and water-repellent cream. It is used as a primer for Drygrip Adhesive and as a salt inhibitor on walls that have just been treated for rising damp with Dryzone Damp-Proofing Cream. Why Dryshield is Required The Dryzone Express Replastering System has revolutionized the process of restoring the decorative surface after a rising damp treatment. Traditional methods required several layers of render and plaster, which was not only time-consuming and messy, but also required significant experience for successful execution. plastic positioning plugs. They are used to set the air gap between the board and the wall before the Dryzone Adhesive cures. DPC products. The machined tool is perfectly sized to fit the 12mm diameter holes that are drilled for The Dryzone System 12mm SDS Masonry Drill Bit is a high-quality drill bit, specially selected for the