Innokin Kroma-Z Pod Mod, E Cigarette Vape Starter Kit 40W 3000mAh Electronic Vaporizer with Z-Coils, 2ml Tank Airflow Control Vaping, LCD Screen Auto-Wattage USB Type-C Fast Charge, No Nicotine, Black

Product Information

Make sure orings, seal and glass are all in good condition and everything is tight. Make sure the coil is fully inserted and lined up correctly, notice cross-threading. When you use RBA coil, make sure you stuff the cotton in there really good. Please try clean the button of your device with a small amount of isopropyl alcohol and a compressed air canister if possible. Apply the alcohol around the edges of the button and let it stand for about 10 seconds before using compressed air to clean the alcohol off. Once the battery is in, I found it satisfyingly firm to close as this door isn’t going to pop open during use or storage.The door has a few vent slits for added safety. Tanky Spanky The Kroma-R is great for big cloud DTL vaping with the Ajax tank or enjoys intense MTL flavors with the full line of Z-coils and Platform series tanks. Currently vaping Just Juice 50/50 Nic Salt Mango and Passion Fruit - tried on both the 0.8 and 1.6 coil - great on both!

Holding up and down brings you into a menu where you can adjust screen on-time (5 to 180s) and Cutoff time (3 to 18s). Make sure the atomizer has been cooled down while you refill the tank because the liquid flows faster when the atomizer is hot. The beeping noise you hear is totally normal and is a symptom of something called pulse-width modulation, or PWM for short. In simple terms, PWM is how the device utilizes the electrical power from the battery to heat up your coil. These pulses of power can approach the frequency range of human hearing in some individuals with an acute sense of sound. Nothing can be done to avoid this noise, however it's nothing to be concerned about regarding the performance or lifespan of your product. For the 0.8Ω Z-Coil, recommended at 15 to 18 Watts, I went with a 50Vg 50PG 20mg Nic Salt – GotSalts – Peachy Promise.I liked the tapered top at the rear which gave it much more style and an alternate firing grip as I found it comfortable to pop my thumb on it.Innokin have made the top and base a contrasting smooth finish which just works with the brushed steel finish of the main body. Warning: If the coils has a sub-ohm resistance, please make sure you have a great understanding and technical knowledge on how to use mods and batteries that can handle Sub-Ohm coils. Do not use short or flat 510 connection on any hybrid or hybrid style device. If you are not familiar or unsure of particular products or set-ups, please do not use it. Always use proper precautions and handling. The Kroma-Z is a equipped with a full range of integrated safety protections you’d expect from Innokin: Overheat protection, Charging protection, Short circuit protection, High Resistance protection, Cut-Off protection and Over-discharge protection.

The Kroma-Z features 1.7Amp USB Type C fast charging. Fast charging is a feature seen in our premium devices which allow you to use a 1.7Amp wall charger and high quality USB-C cable to charge your device. 1.7A charges devices faster than a standard 1Amp or .5Amp charger. Make sure that your Innokin device is Fast Charging compatible before you charge your device with a fast charger. Never leave your device unattended while charging. ElementVape.com and any or all of ElementVape.com’s parent and subsidiary companies will not be held responsible or liable for any injury, damage, or defect, permanent or temporary that may be caused by the improper use of a Li-ion (Lithium-ion), LiPo (Lithium-ion Polymer) and any rechargeable battery/batteries as well as chargers. Please have a greater understanding of the batteries/chargers you are using and how to care for them properly.It is a very comfortable lightweight pod-mod that just lays nice in the hand and is portable. Even tough I don’t have any major scratches yet, I think they will appear over-time like on the Kroma R, but the paint job is well done and feels nice. I wanted a Tight MTL vape with this one, and at 18 watts with both airflow sliders down very low, I certainly got that tight draw I was after and a satisfying vape to boot. Nothing staggering, but decent. Make sure to prime your coil upon first use. 1 drop of e-liquid per cotton juice port is enough. Once primed, allow the coil to stand in a 3/4ths full tank for at least 15 minutes before vaping. Don't take long draws or vaping with very short intervals between two drags. Each puff time shall be 4 seconds at most. Only use Lithium Ion rechargeable batteries in devices that have a built in protection circuit board(PCB) that detect shorts, over-discharge, over-charging etc. Use of lithium ion batteries without a PCB may increase your risk or explosion and,or fire.