276°
Posted 20 hours ago

BIQU Orbiter V2.0 Extruder, with Double Gear Direct Drive

£444.5£889.00Clearance
ZTS2023's avatar
Shared by
ZTS2023
Joined in 2023
82
63

About this deal

IR Probe - uncomment the following 2 lines if you have a and IR Probe, and comment out the BLTouch section below This Orbiter 2.0 Mini Stealth is a better fit than the Orbiter 1.5 Mini Stealth in a V2.4 or Trident as the motor no longer interferes with the path of the cable chain. There is a separate 'strain_relief' stl for use in the V0.1. There are also x-frame pieces that allow this Mini Stealth to be installed on a Switchwire. The nozzle is moved up by 3mm compared to the official Switchwire due to the stepper motor being so low on the Orbiter extruder but this also allows a BL-Touch to fit into the x-frame pieces.

Sailfin and HextrudORT are very similar designs that you may prefer in certain circumstances but they are less popular and you may need to design your own mount to use them. Bondtech LGX Printed parts come without any heat inserts, you will have to mount those by yourself or choose heat insert preinstalled, in the options panel M950 F1 C"fan1" Q25000 ; Set Fan 1 on "Duex2 Fan 1" for Hotend Fan. Use the FAN1 connector for a thermostatically-controlled Flipped drive gears – filament path closer to the extruder center for a more balanced design and perfect fit on delta printers as well The included Blender file shows the entire assembly complete with screws and should answer most basic questions.

Sherpa Mini* is a compact and lightweight open source extruder. It’s using BMG components with a smaller NEMA 14 stepper motor. Due to its compact design and a smaller stepper it weights just 127g. Sherpa Mini uses BMG gears but due to different pinion gear on the NEMA 14 stepper has 5:1 rather than 3:1 gearing ratio. It’s an easy upgrade option for people who already have a BMG extruder: you need to get a NEMA 14 stepper and print a few parts. I haven't made any changes above or below these lines so i the problem MAY be in here################################## The unload button is connected to an input of the control board which is configured to trigger an event which starts the unload macro.

I recommend using a file to lightly remove any printing artifacts on the mating face of the shroud. The IR Probe needs to be screwed into place with two M2.5x8 FHCS before installing any of the fans, except with the VolcoMosq or UHF hotends where the probe needs to be glued on with CA glue. The Y-offset for this probe is 4mm in front of the nozzle and the X-offset is 32mm.I have added new stretched versions that should fit the Rapido UHF, Dragon UHF and the VolcoMosq hotends. The Dragon UHF and Rapido UHF hotends can fit in the same shroud. The UHF hotends will reduce Z travel by 8.5mm and the VolcoMosq by 3mm. I cannot verify the fitment so if there are any issues please leave a comment. P - Sensor type - 1=simple sensor (high signal when filament present), 5= Duet Laser v2.0, 6= Duet Laser v2.0 with microswitch

N.B. If a fan is configured to trigger on a virtual heater whose sensor represents TMC2660 driver over-temperature Volumetric extrusion is an option you can set in some slicers whereby all extrusion amounts are specified in mm3 (cubic millimetres) of filament instead of mm of filament.

  1. Features and Performance

Carefully push the status LED carrier as far as it will go and press the fan into position while making sure not to pinch the part-cooling fan wires. Then press the remaining LEDs into their slots. (I measure out 35mm of wire to connect these LEDs together) The extremely powerful LDO-36STH20-1004AHG LDO stepper motor provides excellent performance with a retraction speed of 120 mm/s and acceleration of up to 8000 mm/s² M906 X1150 Y1150 Z900 E560 I60 ; Motor currents (mA) - WARNING: Conservative - May trigger stallguard (and prematurely during homing) if sensorless. M308 S0 P"bedtemp" Y"thermistor" A"bed_heat" T100000 B3950 R4700 H0 L0 ;_RRF3_ Bed thermistor, connected to bedtemp on Duet2 The Orbiter V2.0 features Bondtech-quality hardened dual drive gears, shortened to 11mm, that grip filament from both sides. The gears have been reversed, which means the filament path is now closer to the extrusion center. Changes to the motor design contribute to the Orbiter V2.0's approximately 40% higher extrusion force and better acceleration performance compared to the previous V1.5 version.

Asda Great Deal

Free UK shipping. 15 day free returns.
Community Updates
*So you can easily identify outgoing links on our site, we've marked them with an "*" symbol. Links on our site are monetised, but this never affects which deals get posted. Find more info in our FAQs and About Us page.
New Comment