276°
Posted 20 hours ago

Victron Energy SmartShunt 500 amp Battery Monitor (Bluetooth)

£9.9£99Clearance
ZTS2023's avatar
Shared by
ZTS2023
Joined in 2023
82
63

About this deal

The 500A model is appropriate for most campervan electrical systems where an amperage between 0-500A is required. If your system requires more than 500A please see the Victron Energy 1000A SmartShunt. Alternatively the SmartShunt can be connected and be read by a GX device. Connection to the SmartShunt is made via a VE.Direct cable. To understand which size inverter you require, you will need to work out the wattage to match your requirements. To do this, you will need to add up the wattage of each 230V appliance you want to use, and find out their rated power draw. Usually the item manual will provide the wattage draw.

In vitro hydrodynamic properties of the miethke ProGAV hydrocephalus shunt. Cerebrospinal Fluid Res. 2006; 3( 1):9. [ PMC free article] [ PubMed] [ Google Scholar]

or you can monitor the midpoint voltage of your battery bank (cable included) to keep an eye on battery health. If you have a laptop which is 60W, a TV which is 51W, and a coffee machine which is 1400W, then your maximum power usage would be 1511W. A few days ago I bought and installed an IP65 SmartShunt to monitor my travel trailer's two house batteries. From the app I can connect to the shunt from about 30 feet away.

Siphon regulatory devices: their role in the treatment of hydrocephalus. Neurosurg Focus. 2007; 22( 4):1–8. [ PubMed] [ Google Scholar] The SmartShunt can do more than comprehensively monitor your main battery bank – additionally you can choose to either: Common LiFePO4 values are: 100Ah, 230Ah, 280Ah and 300Ah. There are of course variations of this. Charged Voltage (v) Please note that if the "Consumed Ah" reading indicates three dashes: “---” this means that the battery monitor is in an unsynchronised state. This mainly occurs when the battery monitor has just been installed or after the battery monitor has been left unpowered and is powered up again. For more information, see the Synchronising the battery monitor chapter.The battery voltage must be above this voltage level to consider the battery as fully charged. As soon as the battery monitor detects that the voltage of the battery has reached the “charged voltage” and the current has dropped below the “tail current” for a certain amount of time, the battery monitor will set the state of charge to 100%. The use of the codman-medos programmable hakim valve in the management of patients with hydrocephalus: illustrative cases. Neurosurgery. 1994; 34( 6):1110–3. [ PubMed] [ Google Scholar] It is important to note that Victron Energy rate their inverters in Volt Amps (VA). The datasheets do also state the wattage of each inverter. That said however, what I can't do from that distance is enter into the shunt's next section in the app to edit the shunts various settings. The app will try to re-connect a few times but fails then stalls. So to fully connect and edit I have to be within a few feet of the device. Not ideal but I figure once it's set up properly I should be good. Time will tell. Example: If a current of 12A is drawn from a fully charged battery for a period of 3 hours, the readout will show -36.0Ah (-12 x 3 = -36).

May I also ask for some advice on installing a Victron battery monitor?At present I have a lot of sep cables going to the 2x new lithium 100ah plus solar ,mains charger, inverter, temp sensors etc. Room is tight for busbars but I can just about fabricate a mounting for the BVM 712 and a sep neg busbar. My understanding is that all negative loads inc solar and inverter then go to the negative busbar ( ? the temp sensors?) then new cable connects neg busbar to load on BVM and then BVM connected to cable from battery negative ( cross wired). Is that correct? The “Charge Efficiency Factor” compensates for the capacity (Ah) losses during charging. A setting of 100% means that there are no losses.Telemetric implantable pressure sensor for short-and long-term monitoring of intracranial pressure. Proceedings of the 29th Annual International Conference of the IEEE EMBS; 2007: 514. [ PubMed]

Effect of 3-tesla magnetic resonance imaging on various pressure programmable shunt valves. J Neurosurg Pediatr. 2005; 103( 2):163–5. [ PubMed] [ Google Scholar] The alarm will activate when the value reaches a set threshold and will deactivate when the value clears this threshold. The thresholds are configurable. For more information, see the Alarm settings chapter. This setting is relatively simple, if you have a single battery it’s really easy (the stated capacity of your battery in Ah) If your battery capacity is stated in Kwh then divide by the voltage of your battery.

It’s important to balance your power usage with your recharge potential.

As soon as the battery monitor detects that the voltage of the battery has reached the set “Charged voltage” parameter and the current has dropped below the “Tail current” for a certain amount of time, the battery monitor will set the state of charge to 100%. Charged Detection Time (m) This is the actual current flowing in or out of the battery. A negative current indicates that current is taken from the battery. This is the current needed for DC loads. A positive current means that current is going into the battery. This is current coming from charge sources. Keep in mind that the battery monitor will always indicate the total battery current, being the current traveling into the battery minus the current traveling out of the battery. CSF shunts 50 years on–past, present and future. Childs Nerv Syst. 2000; 16( 10):800–4. [ PubMed] [ Google Scholar]

Asda Great Deal

Free UK shipping. 15 day free returns.
Community Updates
*So you can easily identify outgoing links on our site, we've marked them with an "*" symbol. Links on our site are monetised, but this never affects which deals get posted. Find more info in our FAQs and About Us page.
New Comment