Selections Fence Trellis Topper Bracket Height Extension Arms Pack (5 Pairs inc Screws)

Product Information

While extending your chain link fence, as mentioned above, is not exactly cheap, it is cheaper than removing your existing fence and replacing it with a completely new fence. Usually, people will build fences to the maximum height that local bylaws allow, so if you want to make your chain link fence higher, you might need special permission to do that. Now pop your first sheet into the bottom rail and slide it into the upright. Ensure you align the profile with the existing fence below. With the first one in place, take note of how and where the sheets on the existing fence overlap each other and continue inserting your remaining sheets, keeping an eye on the alignment of your profile.

existing fence panel in the slot to give firm support to extra trellis (or fence panels) above your existing fencing. Pre-punched holes allow for nail or screw fixing as required. You or your fence installer will not have to pull posts, and you won’t need new posts, rails or concrete bases for your posts, all of which will save money. There is still some cost to take down the old mesh and tension bars, but that shouldn’t be a big part of the labor to extend your chain link fence this way. Should You Extend Your Chain Link Fence Height This Way?The first answer to the question of how to make a chain link fence taller is the simplest option: adding an overhang. Fibre cement would require a more complex 70x35mm treated pine frame to be attached to the top and bottom rails along with vertical lengths at certain points (see installation guides) and noggins to ensure a strong foundation. If the fence material you take down is in good condition, you might be able to resell it as second-hand fencing material. You might also be able to sell it to a metal recycling company.

An important question to consider while you’re finding out how to make a chain link fence taller is whether you should do this instead of installing a new fence. Repeat Step 4 and 5 until all sections are complete. You have now finished your Colorbond fence extensions. Now is the perfect time to clean off any cobwebs and dirt and treat it all with pest spray. The corrosion proof galvanised channels slide down the 2” wide slot of slotted concrete posts and over the In this case, the condition of your fence posts and rails is the biggest deciding factor. If all your posts and rails are in great shape and still straight and level, then this is a great choice. However, if your posts are damaged, bent or rusted, it might be better to replace the whole fence. Chain link fence post extension sleeves should have an inner, smaller diameter piece of pipe, usually about 6 inches long, welded into the outer pipe, which is the same diameter as the fence post.As always, if you’re not sure what the best solution for your chain link fence is, talk to a contractor or installer who specializes in this type of service. Once your material arrives and you are ready to extend your chain link fence height, you will need to take down your existing mesh, remove your top rails and post caps, and remove tension bars. The second answer to the question of how to make a chain link fence taller has more steps, but it allows you to add more height to your fence and does not require you to have barbed or smooth wire on an overhang or extension. Here are the steps you will need to take to extend the height of your chain link fence this way. Please be aware if you are running a 2 wire system you will need 1.2m netting. If you are running a 3 wire system you will need 1.8m netting. ​ Once the chain link fence post extension sleeves are in place, start rebuilding the fence using the new chain link materials and the materials reserved when you took the fence down.

With all your upright extensions in place, slide one end of a rail into an upright, then slide the other end in a downward direction to fit into the upright at the other end of the section. This is your new bottom rail. Once it’s in place, pop a screw in each end and one in the middle to attach it to the top rail of the existing fence. Repeat this step for each section. Two lengths are available, 500mm long for adding 1 to 2 feet extra height and 795mm for adding 1 to 3 feet extra In some cases, when your fence goes above a certain height, you might also need to submit drawings or plans for the fence. Option 1: Add An Overhang An already braced premade timber panel will likely only require some 50 x 25mm treated pine fixed to the top and bottom rails with 14g x 50mm Metal Teks. Then use either colour-matched timber screws or trim head screws to fix the panels to the treated pine frame. Once your chain link fence height has been extended this way, if done properly, it should be just as secure and sturdy as it ever was. Is It Cheaper to Make a Chain Link Fence Taller?